Mitsubishi Electric PUZ-M200YKA2 Скачать руководство пользователя страница 2

Страница: 2 / 114

OCH775

2-1. ALWAYS OBSERVE FOR SAFETY

Before obtaining access to terminal, all supply circuits must be disconnected.

INDOOR UNIT SERVICE MANUAL

Model Name

Service Ref.

Service manual No.

Parts catalog No.

PLA-M50/60/71/100/125EA2

PLA-M50/60/71/100/125EA2.UK

—

PCA-M71HA2

OCH753

OCB753

PCA-M50/60/71/100/125KA2

OCH752

OCB752

PKA-M50LA(L)2

.TH

—

PKA-M60/71/100KA(L)2

PKA-M60/71/100KA(L)2.TH

—

PSA-M71/100/125KA

OCH724

OCB724

PEAD-M50/60/71/100/125JA(L)2

PEAD-M50/60/71/100/125JA(L)2.UK

—

PEA-M200/250LA

HWE20020

BWE020180

SAFETY PRECAUTION

2-2. CAUTIONS RELATED TO NEW REFRIGERANT

Cautions for units utilizing refrigerant R32

Preparation before the repair service.

• Prepare the proper tools.

• Prepare the proper protectors.

• Provide adequate ventilation.

• After stopping the operation of the air conditioner, turn off

the power-supply breaker.

• Discharge the condenser before the work involving the

electric parts.

Precautions during the repair service.

• Do not perform the work involving the electric parts

with wet hands.

• Do not pour water into the electric parts.

• Do not touch the refrigerant.

• Do not touch the hot or cold areas in the refrigerating cycle.

• When the repair or the inspection of the circuit needs to be

done without turning off the power, exercise great caution

not to touch the live parts.

• When opening or closing the valve below freezing

temperatures, refrigerant may spurt out from the gap

between the valve stem and the valve body, resulting in

injuries.

REFERENCE MANUAL

MEANINGS OF SYMBOLS DISPLAYED ON THE UNIT

WARNING

(Risk of fire)

This mark is for R32 refrigerant only. Refrigerant type is written on nameplate of outdoor unit.

In the case that refrigerant type is R32, this unit uses a flammable refrigerant.

If refrigerant leaks and comes in contact with fire or heating part, it will create harmful gas and there is risk of fire.

Read the OPERATION MANUAL carefully before operation.

Service personnel are required to carefully read the OPERATION MANUAL and INSTALLATION MANUAL before operation.

Further information is available in the OPERATION MANUAL, INSTALLATION MANUAL, and the like.

Содержание PUZ-M200YKA2



















































































































Результаты поиска

Содержание PUZ-M200YKA2

Отзывы:

Похожие инструкции для PUZ-M200YKA2

Бренды по названию

Популярные бренды

Mitsubishi Electric PUZ-M200YKA2, Руководство по обслуживанию

Результаты поиска

Содержание PUZ-M200YKA2

Отзывы:

Похожие инструкции для PUZ-M200YKA2

Бренды по названию

Популярные бренды