Mitsubishi Electric MUZ-FH25VE-E1 Скачать руководство пользователя

Страница: 40 / 55

Press OPERATE/STOP (ON/OFF) button of the remote

controller (the set temperature is displayed) with the

remote controller headed towards the indoor unit. 1

Expansion valve operates in full-opening direction.

NOTE

: After check of LEV, do the undermentioned operations.

1. Turn OFF the power supply and turn it ON again.

2. Press RESET button on the remote controller.

1. Regardless of normal or abnormal condition, a short beep

is emitted once the signal is received.

Measure each voltage between connector

pins of CN724 on the inverter P.C. board.

1. Pin (-) — Pin (+)

2. Pin (-) — Pin (+)

3. Pin (-) — Pin (+)

4. Pin (-) — Pin (+)

Is there about 3 - 5 VAC between each?

NOTE:

Measure the voltage by an analog

tester.

Properly

x the LEV coil to the expansion valve.

Replace the inverter P.C.

board.

Replace the LEV coil.

Replace the expansion valve.

Is LEV coil properly

xed to

the expansion valve?

Does the resistance of LEV

coil have the characteristics?

(Refer to 11-4.)

Do you hear the expansion valve "click,

click·······"?

Do you feel the expansion valve vibrate

on touching it ?

Turn ON the power supply.

While pressing both OPERATION SELECT button

and TEMP button on the remote controller at the

same time, press RESET button.

First, release RESET button.

Hold down the other two buttons for another 3 sec-

onds. Make sure that the indicators on the LCD screen

shown in the right

gure are all displayed. Then re-

lease the buttons.

Yes

K Check of LEV (Expansion valve)

OBH624B

Содержание MUZ-FH25VE-E1
























































Результаты поиска

Содержание MUZ-FH25VE-E1

Отзывы:

Похожие инструкции для MUZ-FH25VE-E1

Бренды по названию

Популярные бренды

Mitsubishi Electric MUZ-FH25VE-E1, Руководство по обслуживанию

Результаты поиска

Содержание MUZ-FH25VE-E1

Отзывы:

Похожие инструкции для MUZ-FH25VE-E1

Бренды по названию

Популярные бренды