background image

34

11-5. TROUBLESHOOTING FLOW

 A  How to check inverter/compressor

Refer to 11-5.  “Check of compressor 

operation time”.

Does the compressor operate continuously?

Refer to 11-5.  “Check of compressor start failure”.

OK.

No

Yes

Refer to 11-5.  “Check of compressor 

winding”.

Is the compressor normal?

Replace the compressor.

No

Yes

 B  Check of open phase

 C  Check of compressor

 With the connector between the compressor and the power module (IC700)

 (MUZ-FH25/35

)/IGBT module (IC700) (

MUZ-FH50

disconnected, activate the inverter and check if the inverter is normal by measuring 

the voltage balance

 between the termi-

nals.

  Output voltage is 50 - 130 V. (The voltage may differ according to the tester.)

<< Operation method>>

  Start cooling or heating operation by pressing EMERGENCY OPERATION switch on the indoor unit. (TEST RUN OPERA-

TION: Refer to 8-3.)

<<Measurement point>>

  At 3 points

  BLK (U)-WHT (V)

  BLK (U)-RED (W)

 WHT(V)-RED (W)

NOTE

: 1. Output voltage varies according to power supply voltage.

 

2. Measure the voltage by analog type tester.

 

3. During this check, LED of the inverter P.C. board 

fl

 ashes 9 times. (Refer to 11-6.1.)

 Measure AC voltage between the lead wires at 3 points.

Are the voltages balanced?

Disconnect the connector between the compressor 

and the power module (IC700) (

MUZ-FH25/35

)/IGBT 

module (IC700) (

MUZ-FH50

).

Replace the inverter P.C. board.

Check the voltage between terminals.

Check the compressor.

See 11-5.  “Check of compressor”.

No

Yes

See 11-5.  “Check of open phase”.

OBH624B

Содержание MUZ-FH25VE-E1
























































Отзывы: