background image

22

OPERATING PROCEDURE

PHOTOS

Photo 4

Photo 6

Vane motors

Indoor
coil
thermistor

Photo 3

3. Removing the electrical box

(1) Remove the front panel. (Refer to 1.)
(2) Remove the electrical cover. (Refer to 2.)
(3) Disconnect the connector of the indoor coil thermistor.
(4) Disconnect the motor connector (CN211 and CN121) and

the vane motor connector (CN151) on the electronic 
control P.C. board.

(5) Remove the screws of earth wire.
(6) Remove the fan motor lead wire and indoor coil thermistor

from the electrical box.

(7) Remove the lead wire of vane motor from the bottom of

electrical box.

(8) Remove the screw fixing the electrical box and remove the

electrical box.

4. Removing the vane motor

(1) Remove the front panel. (Refer to 1.)
(2) Remove the electrical cover. (Refer to 2.)
(3) Remove the lead wire of vane motor. (Refer to 3.)
(4) Remove the R.L. holder.
(5) Pull out the drain hose from the nozzle assembly and

remove the nozzle assembly.

(6) Remove the screws of the vane motor and disconnect the

connector.

(7) Remove the vane motor.

Screws fixing the fan motor

5. Removing the line flow fan and the indoor fan motor

(1) Remove the front panel. (Refer to 1.)
(2) Remove the electrical box. (Refer to 3.)
(3) Pull out the drain hose from the nozzle assembly and

remove the nozzle assembly.

(4) Remove the water cut.
(5) Slide the hole cover and remove the hole cover.
(6) Remove the hexagon socket set screw from the line flow

fan.

(7) Remove the screws fixing the fan motor and remove the

fan motor. (Be careful not to drop the fan motor because it
is heavy.)

(8) Remove the screws fixing the left side of the heat 

exchanger.

(9) Lift the left side of the heat exchanger.
(10) Remove the line flow fan.

Screws fixing
the left side
of the heat
exchanger

Screws
of the
vane
motor

Screws of the
vane motor

Vane motor

Screw of the
electrical box 

Screws of the earth wire

Photo 5

Photo 7

Photo 8

Hole
cover

Water cut

Screw of the
electrical cover

OB367D-1.qxp  12.1.13 7:49 AM  Page 22

OB367D

Содержание MSH-GA50VB- E1





























Отзывы: