Mitsubishi Electric Mr. Slim PU-P100VKA Скачать руководство пользователя

Страница: 69 / 111

OCH670

Indication

Error

Check

code*

Outdoor controller board

Contents

Inspection method

LED1 (Green) LED2 (Red)
3 blinking 1 blinking

2 blinking

3 blinking

*Check code displayed on remote controller

**Refer to indoor unit’s Service Manual.

4 blinking

5 blinking

6 blinking

7 blinking

1 blinking

2 blinking

3 blinking

4 blinking

Abnormality of comp. surface

thermistor(TH33) and discharge

temperature (TH4)

Abnormality of superheat due

to low discharge temperature

Check if stop valves are open.

Check if connectors (TH4, TH33, LEV-A and LEV-B) on outdoor controller

board are not disconnected.

Check if unit is filled with specified amount of refrigerant.

Measure resistance values among terminals on indoor valve and

outdoor linear expansion valve using a tester.

Abnormal high pressure (High

pressure switch 63H operated.)

Abnormality of outdoor fan

motor rotational speed

Check if indoor/outdoor units have a short cycle on their air ducts.

Check if connector (63H) on outdoor controller board is not disconnected.

Check if heat exchanger and filter is not dirty.

Measure resistance values among terminals on linear expansion valve

using a tester.

Check if stop valves are open.

Check looseness, disconnection, and converse connection of

compressor wiring.

Measure resistance values among terminals on compressor using a tester.

Check if outdoor unit has a short cycle on its air duct.

Compressor overcurrent

breaking(Startup locked)
Compressor overcurrent breaking

Abnormality of current sensor (P.B.)
Abnormality of power module

Open/short of discharge thermistor (TH4)

and comp. surface thermistor (TH33)

Open/short of outdoor thermistors

(TH6, TH7 and TH8)

Check if connectors(TH3,TH4,TH6 ,TH7, TH8 and TH33) on outdoor

controller board and connector (CN6) on outdoor power board are

disconnected.

Measure resistance value of outdoor thermistors.

Abnormality of heatsink

temperature

Check if indoor/outdoor units have a short cycle on their air ducts.

Measure resistance value of outdoor thermistor(TH8).

Check the outdoor fan motor.

Check if connector (TH3) on outdoor controller board is disconnected.

Abnormality of voltage

Check looseness, disconnection, and converse connection of

compressor wiring.

Measure resistance value among terminals on compressor using a tester.

Check if power supply voltage decreases.

Check the wiring of CN52C.

Abnormality of room temperature thermistor (TH1)

Abnormality of pipe temperature thermistor /Liquid (TH2)

Abnormality of pipe temperature

thermistor/Condenser-Evaporator

Check if connectors (CN20, CN21, CN29 and CN44) on indoor

controller board are not disconnected.

Measure resistance value of indoor thermistors.

Abnormality of drain sensor (DS)

Float switch(FS) connector open

Indoor drain overflow protection

Check if connector (CN31)(CN4F) on indoor controller board is not

disconnected.

Measure resistance value of indoor thermistors.

Measure resistance value among terminals on drain pump using

a tester.

Check if drain pump works.

Check drain function.

Freezing (cooling)

Check if indoor unit has a short cycle on its air duct.

Check if heat exchanger and filter is not dirty.

Measure resistance value on indoor and outdoor fan motors.

Check if the inside of refrigerant piping is not clogged.

Abnormality of pipe

temperature

Check if indoor thermistors(TH2 and TH5) are not disconnected from holder.

Check if stop valve is open.

Check converse connection of extension pipe. (on plural units connection)

Check if indoor/outdoor connecting wire is connected correctly.

(on plural units connection)

P.35

P.36

P.35

P.36

P.38

P.39

P.38

P.36

P.35

P.36

P.37

Detailed

reference

page

Содержание Mr. Slim PU-P100VKA
















































































































Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr. Slim PU-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды