Mitsubishi Electric Mr. Slim PU-P100VKA Скачать руководство пользователя

Страница: 15 / 111

OCH670

7-2. SEPARATE INDOOR UNIT/ OUTDOOR UNIT POWER SUPPLIES

The following connection patterns are available.

The outdoor unit power supply patterns vary on models.

1:1 System

The optional indoor power supply terminal kit is required.

S2
S3

Affix a label B that is included with the manuals near each wiring diagram for the indoor and outdoor units.

Outdoor unit power supply

Earth leakage breaker

Wiring circuit breaker or isolating switch

Outdoor unit

Indoor unit/outdoor unit connecting cords

Remote controller

Indoor unit

Option

Indoor unit power supply

If the indoor and outdoor units have separate power supplies, refer to the table below.

If the optional indoor power supply terminal kit is used, change the indoor unit

electrical box wiring referring to the figure in the right and the DIP switch settings of

the outdoor unit control board.

Indoor power supply terminal kit (option)

Indoor unit electrical box connector con-

nection change

Label affixed near each wiring diagram

for the indoor and outdoor units

Outdoor unit DIP switch settings (when

using separate indoor unit/outdoor unit

power supplies only)

Indoor unit specifications

Required
Required

Required

Electric heater

(For models with

heater)

Connectors (connections when shipped
from the factory are for indoor unit power
supplied from outdoor unit)

Indoor unit power supplied from outdoor unit

(when shipped from factory)

If the indoor and
outdoor units have
separate power

supplies, change the
connections of the
connectors as shown

in the following
figure.

Connectors

Indoor unit

control board

Separate indoor unit/outdoor unit power
supplies

Electric heater

(For models with

heater)

S1
S2
S3

BLUE

YELLOW

CND

CN01

ORANGE

CN01

ORANGE

S1
S2
S3

YELLOW

BLUE

YELLOW

CND

Indoor unit

control board

Note:

There are 3 types of labels (labels A, B, and C). Affix the appropriate labels to

the units according to the wiring method.

OFF

Set the SW8-3 to ON.

1 2

(SW8)

Simultaneous twin/triple system

Affix a label B that is included with the manuals near each wiring diagram for the indoor and outdoor units.

<For models without heater>

The optional indoor power supply terminal kit is required.

Outdoor unit power supply

Earth leakage breaker

Wiring circuit breaker or isolating switch

Outdoor unit

Indoor unit/outdoor unit connecting cables

Remote controller

Indoor unit

Option

Indoor unit power supply

Indoor unit earth

S1
S2
S3

1
2

S1
S2
S3

1
2

S1
S2
S3

1
2

*1. A breaker with at least 3 mm contact separation in each pole shall be provided. Use earth leakage breaker (NV).

The breaker shall be provided to ensure disconnection of all active phase conductor of the supply.

*2. Max. 120 m

*3. Max. 500 m (Max. 200 m when 2 remote controllers are used)

*4.The figures are NOT always against the ground.

Notes: 1. Wiring size must comply with the applicable local and national code.

2. Power supply cables and indoor unit/outdoor unit connecting cables shall not be lighter than polychloroprene sheathed

flexible cable. (Design 60245 IEC 57)

3. Install an earth line longer than power cables.

Indoor unit model

Indoor unit power supply

Indoor unit input capacity

Main switch (Breaker)

Indoor unit power supply

Indoor unit power supply earth

Indoor unit-Outdoor unit

Indoor unit-Outdoor unit earth

Remote controller-Indoor unit

Indoor unit L-N

Indoor unit-Outdoor unit S1-S2

Indoor unit-Outdoor unit S2-S3

Remote controller-Indoor unit

50–140

~/N (single), 50 Hz, 230 V

16 A

Min. 1.5

Min. 0.3

–

0.3 (Non-polar)

230 V AC

–

24 V DC

12 V DC

Circuit

rating

Wiring

Wire No.

size

(mm

)

Содержание Mr. Slim PU-P100VKA
















































































































Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr. Slim PU-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды