Mitsubishi Electric Mr. Slim PU-P100VKA Скачать руководство пользователя

Страница: 43 / 111

OCH670

Continued to the next page.

Check code

Abnormal points and detection method

Case

Judgment and action

(6607)

NO ACK signal

1. Transmitting side controller detects

abnormal if a message was transmitted

but there is no reply (ACK) that a

message was received. Transmitting

side detects abnormality every 30

seconds, 6 times continuously.

Note:

The address and attribute displayed at

remote controller indicate the controller

that did not reply (ACK).

Common factor that has no

relation with abnormality source

The unit of former address

does not exist as address

switch has changed while the

unit was energized.

Extinction of transmission wire

voltage and signal is caused

by over-range transmission

wire.

• Maximum distance

.......200m

• Remote controller line

..(12m)

Extinction of transmission wire

voltage and signal is caused by

type-unmatched transmission

wire.

Type......

With shield wire-

CVVS, CPEVS

With normal wire (no shield)-

VCTF, VCTFK, CVV

CVS, VVR, VVF, VCT

Diameter.....1.25mm

or more

Extinction of transmission wire

voltage and signal is caused

by over-numbered units.

Accidental malfunction of

abnormality-detected controller

(noise, thunder surge)

Defective of abnormality-

generated controller

2. If displayed address or attribute is

outdoor unit, indoor unit detects

abnormality when indoor unit transmits

signal to outdoor unit and there was no

reply (ACK).

Contact failure of transmission

wire of outdoor unit or indoor

unit

Disconnection of transmission

connector (CN2M) of outdoor

unit

Defective transmitting receiving

circuit of outdoor unit or indoor

unit

Always try the following when the error

“A7” occurs.

Turn off the power supply of outdoor

unit, indoor unit and FRESH MASTER or

LOSSNAY at the same time for 2 minutes

or more, and turn the power on again. If

malfunction was accidental, the unit returns

to normal.

Check address switch of abnormality-

generated address.

Check disconnection or looseness of

abnormality-generated or abnormality-

detected transmission wire (terminal block

and connector)

Check if tolerance range of transmission wire

is not exceeded.

Check if type of transmission wire is correct

or not.

If the cause of trouble is not any of

–

above, repair the defect, then turn off the power

supply of outdoor unit, indoor unit and FRESH

MASTER or LOSSNAY at the same time for 2

minutes or more, and turn the power on again.

• If the cause of trouble is not any of

above in single refrigerant system (one

outdoor unit), controller of displayed address

or attribute is defective.

• If the cause of trouble is not any of

–

above in different refrigerant system (2 or

more outdoor units), judge with

If address of abnormality source is the

address that should not exist, there is the

unit that memorizes nonexistent address

information. Delete useless address

information with manual setting function of

remote controller.

Only the system FRESH MASTER or

LOSSNAY are connected to, or the system

that is equipped with group setting of

different refrigerant system.

If the cause of trouble is not any of

–

above, replace the controller board of displayed

address or attribute.

If the unit does not return normally, multi-

controller board of outdoor unit may be

defective (repeater circuit).

Replace multi-controller board one by one to

check if the unit returns normally.

3. If displayed address or attribute is

indoor unit, remote controller detects

abnormality when remote controller

transmits signal to indoor unit and there

was no reply (ACK).

During group operation with

indoor unit of multi- refrigerant

system, if remote controller

transmits signal to indoor

unit while outdoor unit power

supply of one refrigerant

system is turned off or within 2

minutes of restart, abnormality

is detected.

Contact failure of transmission

wire of remote controller or

indoor unit

Disconnection of transmission

connector (CN2M) of indoor

unit

Defective transmitting receiving

circuit of indoor unit or remote

controller

Содержание Mr. Slim PU-P100VKA
















































































































Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr. Slim PU-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды