Mitsubishi Electric Mr. Slim PU-P100VKA Скачать руководство пользователя

Страница: 45 / 111

OCH670

9-5. TROUBLESHOOTING OF PROBLEMS

Phenomena

Factor

Countermeasure

1. Remote controller display does not

work.

2. “PLEASE WAIT” display is remained

on the remote controller.

3. When pressing the remote controller

operation switch, the OPERATION

display is appeared but it will be

turned off soon.

After cancelling to select function from the remote

controller, the remote controller operation switch will

be not accepted for approx. 30 seconds.

Normal operation

At longest 2 minutes after the power supply “PLEASE

WAIT” is displayed to startup.

Communication error between the remote controller

and indoor unit

Communication error between the indoor and out-

door unit

Outdoor unit protection device connector is open.

12 V DC is not supplied to remote controller.

(Power supply display is not indicated on LCD.)

12–15 V DC is supplied to remote controller, how-

ever, no display is indicated.

•

“PLEASE WAIT” is not displayed.

•

“PLEASE WAIT” is displayed.

Check LED2 on indoor controller board.

(1) When LED2 is lit.

Check the remote controller wiring for

breaking or contact failure.

(2) When LED2 is blinking.

Check short circuit of remote controller

wiring.

(3) When LED2 is not lit.

Refer to phenomena No.3 below.

Check the following.

•

Failure of remote controller if “PLEASE

WAIT” is not displayed

•

Refer to phenomena No.2 below if

“PLEASE WAIT” is displayed.

Normal operation

Self-diagnosis of remote controller

”PLEASE WAIT” is displayed for 6 min-

utes at most in case of indoor/outdoor

unit communication error. Check LED3 on

indoor controller board.

(1) When LED3 is not blinking.

Check indoor/outdoor connecting wire

for Miswiring.

(Converse wiring of S1 and S2, or

break of S3 wiring.)

(2) When LED3 is blinking.

Indoor/outdoor connecting wire is

normal.

Check LED display on outdoor controller

circuit board. Refer to "9-10. FUNCTION OF

SWITCHES, CONNECTORS AND JUMPERS"

Check protection device connector (63H)

for contact failure.

Refer to "9-9. TEST POINT DIAGRAM".

Check code

Abnormal points and detection method

Case

Judgment and action

(6608)

M-NET NO RESPONSE

Abnormal if a message was transmitted

and there were reply (ACK) that message

was received, but response command

does not return. Transmitting side detects

abnormality every 30 seconds, 6 times

continuously.

Note:

The address and attribute displayed at

remote controller indicate the controller

that did not reply (ACK).

Transmitting condition is

repeated fault because of

noise and the like.

Extinction of transmission wire

voltage and signal is caused

by over-range transmission

wire.

• Maximum distance

...... 200m

• Remote controller line

(12m)

Extinction of transmission wire

voltage and signal is caused

by type-unmatched transmis-

sion wire.

Type.........

With shield wire-

CVVS, CPEVS

With normal wire (no shield)-

VCTF, VCTFK, CVV

CVS, VVR, VVF, VCT

Diameter ..... 1.25mm

or more

Accidental malfunction of

abnormality-generated control-

ler

Check transmission waveform or noise on

transmission wire.

Turn off the power supply of outdoor unit

and indoor unit and FRESH MASTER or

LOSSNAY at the same time for 2 minutes or

more, and turn the power on again. If mal-

function was accidental, the unit returns to

normal. If the same abnormality generates

again, controller of displayed address and

attribute may be defective.

Содержание Mr. Slim PU-P100VKA
















































































































Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr. Slim PU-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr. Slim PU-P100VKA

Отзывы:

Похожие инструкции для Mr. Slim PU-P100VKA

Бренды по названию

Популярные бренды