Mitsubishi Electric LY2-3300-B0B Скачать руководство пользователя страница 9

Страница: 9 / 12

Adjustment of the feed foot

and the presser foot

1 . To change the balance of the alternating

movements between the feed foot and presser foot

( 1 ) For example, to increase the rise of the feed

foot, and decrease the rise of the presser foot.

①Turn the pulley until the presser foot is

slightly raised from the throat plate.

②Loosen the set screw Ⓐ (on the right side)

located on the feed lifting rock shaft crank (right).

③The built-in spring pulls down the presser

foot until it makes contact with the throat

plate. Then, tighten the set screw Ⓐ.

④This completes the adjustment, i.e., the

protrusion of the presser foot has been

decreased by a set distance. And, the

vertical motion of the feed foot has been

increased by that same distance.

( 2 ) As a contrary case ( 1 ), to decrease the rise of the

feed foot, and increase the rise of the presser foot.

First, turn the pulley until the feed foot is

slightly raised from the throat plate. Next,

loosen the screw Ⓐ. Finally, tighten the

screw Ⓐ again.

This decreases the rise of the feed foot.

2 . Adjustment of the movement height of the

presser foot and feed foot

Note: When sewing a thin fabric, the up and down

movement should be adjusted at minimum.

●To adjust, loosen the screw, and shift the

position of crank rod boss.

Upward → The up and down movement

will increase. (Max. 5 mm)

Downward → The up and down movement

will decrease. (Min. 2 mm)

3 . A gap between the feed foot and the presser foot

Note: At the condition the stitch length is at max., the

min. gap between the feed foot and the presser

foot is adjusted to be 5 mm as standard.

●Loosen the screw Ⓐ, then turn the feed

driving shaft, so that the gap Ⓑ can be

adjusted.

After adjusting, fully tighten the screw Ⓐ.

4 . Proper timing between the upper and lower feed

Note: Although the upper feed amount (feed foot)

adjust the lower feed amount (feed dog)

are adjusted by 1:1, please adjust the upper

feed amount increasingly or decreasingly,

according to the material to be sewn.

●To adjust, loosen the nut and shift the square

block up and down.

Upward → Feeding amount will decrease

Downward → Feeding amount will increase

Nut

Feed lifting rock

shaft crank (left)

Screw Ⓐ

5 mm Ⓑ

Feed foot

Presser foot

Feed driving shaft crank (right)

Feed driving shaft

Screw

Large

Small

Crank rod

Feed lifting rock shaft crank (right)

Ⓐ

HOW TO USE

— 6 —

Содержание LY2-3300-B0B













Результаты поиска

Содержание LY2-3300-B0B

Отзывы:

Похожие инструкции для LY2-3300-B0B

Бренды по названию

Популярные бренды

Mitsubishi Electric LY2-3300-B0B, Инструкция по эксплуатации

Результаты поиска

Содержание LY2-3300-B0B

Отзывы:

Похожие инструкции для LY2-3300-B0B

Бренды по названию

Популярные бренды