Mitsubishi Electric LY2-3300-B0B Скачать руководство пользователя страница 7

Страница: 7 / 12

Balance of threads tension

Adjustment of the needle

thread tension

● The needle thread tension should be adjusted

on the basis of the bobbin thread tension.

● Adjust the needle thread tension by turning the

thread tension nut.

The needle thread tension can be also adjusted

by changing intensity and movable range of
the thread take-up spring in case of sewing the
special fabric and thread.

Threading of the needle thread

With the thread take-up lever located at the upper
most position, pass the needle thread in the order
shown in the following figure.

Adjustment of feed (stitch)

length and backstitch

● Adjustment of feed (stitch) length…Adjust feed

length by turning the feed length setting dial
while depressing the reverse sewing lever.

● Backstitch…Direction of stitching can be

reversed by depressing the reverse sewing
lever.

A ○

B ×

C ×

Balanced tension

Tight the needle thread tension or

loose the bobbin thread tension

Loose the needle thread tension or

tight the bobbin thread tension

Thread tension nut

Tighten

Loosen

Feed length

setting dial

Reverse sewing

lever

②

⑥

③

④

⑤

⑪

⑩

⑨

⑧

⑦

①

HOW TO USE

— 4 —

Содержание LY2-3300-B0B













Результаты поиска

Содержание LY2-3300-B0B

Отзывы:

Похожие инструкции для LY2-3300-B0B

Бренды по названию

Популярные бренды

Mitsubishi Electric LY2-3300-B0B, Инструкция по эксплуатации

Результаты поиска

Содержание LY2-3300-B0B

Отзывы:

Похожие инструкции для LY2-3300-B0B

Бренды по названию

Популярные бренды