Mitsubishi Electric LY2-3300-B0B Скачать руководство пользователя страница 8

Страница: 8 / 12

Adjustment of the bobbin

thread tension

1 . The bobbin thread tension can be adjusted

by turning the screw Ⓐ.

Adjustment of the presser foot

pressure

1 . Adjust the presser foot pressure according to

the fabric by turning the pressure adjusting
screw.

2 . Pressure on the both the presser foot and

the feed foot can be adjusted. (The adjusting
screw position is factory-adjusted as shown in
the figure.)

3 . Sewing pressure should be adjusted to the

minimum required strength.

Adjustment of the feed dog

height

1 . Turn the pulley and stop it at the position

where the feed lifting rock shaft crank (right)
swings to the innermost position.

2 . Loosen the screw Ⓐ.

Note: Be careful not to move the feed lifting
rock shaft crank (right) in the lateral direction.

3 . Adjust the feed dog height by swinging the

feed lifting rock shaft crank (left) and moving
the feed bar.

4 . After adjusting, fully tighten the screw Ⓐ.

The feed dog height is factory-adjusted to 1.0 mm.

Screw Ⓐ

Thread tension spring

Loosen

Tighten

30 mm

Strengthen

Weaken

Standard

Throat plate

1.0 mm

Feed dog

Feed lifting rock shaft crank (left)

Feed bar

Screw Ⓐ

Feed lifting rock

shaft crank (right)

20 mm

Standard

Strengthen

Weaken

HOW TO USE

— 5 —

Содержание LY2-3300-B0B













Результаты поиска

Содержание LY2-3300-B0B

Отзывы:

Похожие инструкции для LY2-3300-B0B

Бренды по названию

Популярные бренды

Mitsubishi Electric LY2-3300-B0B, Инструкция по эксплуатации

Результаты поиска

Содержание LY2-3300-B0B

Отзывы:

Похожие инструкции для LY2-3300-B0B

Бренды по названию

Популярные бренды