background image

11

Test Run 

Step

What to check for 

Check

1

Check the power supply voltage 

Is single

-

phase 220

-

240V power being used? 

Incorrect power supply may cause malfunctions. 

2

Turn the ground-fault circuit 
interrupter on

Is the power lamp in the display on? 

3

Insert your hands to check if air is 
being blown.

Is the air blowing? 

4

Insert your hands to check if warm 
air is being blown.
(Only with the JT-SB216JSH2 type 
when the heater is "ON".)
(The JT-SB216KSN2 model does not 
have a heater)

Is warm air blowing? 
( If the room temperature is above 30ºC, for safety reasons 

the heater will not operate even if the heater switch is 
turned on.

  As the heater is a simple heater, if the room temperature 

is less than 18ºC, the air may feel cold. 

Is the heater lamp in the display on? 

5

Is the appliance mounted securely without any vibration or 
abnormal noises?

Do not turn the ground-fault circuit interrupter on while hands or other objects are inside the hand drying area. 

 If the display lamp fl ashes, turn the ground-fault circuit interrupter "OFF", check that all of the lamps on the display 

section are off, and then wait for 1 minute before switching the ground-fault circuit interrupter back "ON".

HEAD OFFICE: TOKYO BLDG., 2

-

7

-

3, MARUNOUCHI, CHIYODA

-

KU, TOKYO 100

-

8310, JAPAN

  AUTHORIZED REPRESENTATIVE IN EU:
  MITSUBISHI ELECTRIC EUROPE B.V.
  HARMAN HOUSE, 1 GEORGE STREET, UXBRIDGE, MIDDLESEX UB8 1QQ, U.K.

Содержание JT-SB216JSH2-H-NE
















Отзывы: