6
ITEM
ASCII
HEX
VALUE
HOLD
HLD
48h 4Ch 44h
0 (OFF), 1 (ON)
HOLD BEGIN
HLB
48h 4Ch 42h
00–99
HOLD END
HLE
48h 4Ch 45h
00–99
HOLD
HLD
48h 4Ch 44h
0 (OFF), 1 (ON)
HOLD BEGIN
HLB
48h 4Ch 42h
00–99
HOLD END
HLE
48h 4Ch 45h
00–99
CLAMP POSITION
CLP
43h 4Ch 50h
001–255
CLAMP WIDTH
CLW
43h 4Ch 57h
01–63
VERT. SYNC
VSC
56h 53h 43h
0 (OFF), 1 (AUTO)
LPF
LPF
4Ch 50h 46h
0 (OFF), 1 (ON)
SHUTTER(U)
SHU
53h 48h 55h
00–20
SHUTTER(L)
SHL
53h 48h 4Ch
00–20
SHUTTER(LS)
SHLS
53h 48h 4Ch 53h
00–20
SHUTTER(RS)
SHRS
53h 48h 52h 53h
00–20
*1) Setting range differs depending on the input signals.
• Some commands are not executed depending on the input signal. The operational restrictions same as those
on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII
‘+’
‘-’
‘0’
‘1’
‘2’
‘3’
‘4’
‘5’
‘6’
‘7’
‘8’
‘9’
HEX
2Bh
2Dh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector
Description
30 30 41 50 4F 4E 31 0D
‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’
Command for setting the AUTO
POWER ON to ON
30 30 41 50 4F 4E 31 0D
‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’
Command receipt con
fi
rmation
(Command echo back)
[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the
CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector
Description
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘ ’
Command for setting the picture
control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘ ’
Command receipt con
fi
rmation
(Command echo back)
[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in
quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector
Description
30 30 53 0D
‘0’ ‘0’ ‘S’ ‘ ’
Command for checking the TINT
setting
30 30 53 2B 31 30 0D
‘0’ ‘0’ ‘S’ ‘+’ ‘1’ ‘0’ ‘ ’
Check result (+10)
[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL. (Figures and symbols
enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector
Description
30 30 43 45 55 31 47 53 32 0D
‘0’ ‘0’ ‘C’ ‘E’ ‘U’ ‘1’ ‘G’ ‘S’ ‘2’ ‘ ’
Command for setting the picture
control
30 30 43 45 55 31 47 53 32 0D
‘0’ ‘0’ ‘C’ ‘E’ ‘U’ ‘1’ ‘G’ ‘S’ ‘2’ ‘ ’
Command receipt con
fi
rmation
(Command echo back)
