Panasonic PT-JX200FBE Installation Instructions Manual Download

Page: 1 / 30

DPQX1149ZA

Model No.

ET-JPC200BE

ET-JPC200WE

Installation Instructions

Mount Bracket

Thank you for purchasing this Panasonic product.

■

To customers

This manual is intended for use by installation personnel. Be sure to employ certified personnel to perform the

installation.

After installation, have the installation personnel return this manual to you, and save it for future use.

When moving or removing the projector, give this manual to the certified personnel and have them perform the procedure.

■

To installation personnel

Read the instructions thoroughly and then perform the installation correctly and safely.

Be sure to read through the section entitled “Read this first!” (



pages 3 to 5) before proceeding with the

installation.

After installation, return this manual to the customer.

* Above illustration is shown in combination of this product and optional projector.

ENGLISH

ENGLISH

FRANÇAIS

DEUTSCH

PУССКИЙ

Summary of Contents for PT-JX200FBE































Search results

Summary of Contents for PT-JX200FBE

Reviews:

Related manuals for PT-JX200FBE

Brands by name

Popular brands

Panasonic PT-JX200FBE, Installation Instructions Manual

Search results

Summary of Contents for PT-JX200FBE

Reviews:

Related manuals for PT-JX200FBE

Brands by name

Popular brands