manualshive.com logo in svg

Mitsubishi Electric EHWT17D-MHEDW, Руководство по установке

Поделиться
Скачать
Mitsubishi Electric EHWT17D-MHEDW Скачать руководство пользователя страница 49

Service and Maintenance

7

48

en

Error Codes (C.B.)

Code

Error

Cause

Action

None

―

1

No voltage is supplied to terminal 

block (TB1) of heat pump unit.

a) Power supply breaker is turned off.

b) Contact failure or disconnection of 

power supply terminal

c) Open phase (L or N phase)

1

Check following items.

a) Power supply breaker

b) Connection of power supply terminal 

block (TB1)

c) Connection of power supply terminal 

block (TB1)

2

Electric power is not charged to power 

supply terminal of power circuit board.

a) Contact failure of power supply 

terminal

b) Open phase on the power circuit 

board

2

Check following items.

a) Connection of power supply terminal 

block (TB1)

b) Connection of terminal on power cir-

cuit board

Check connection of the connector LI 

or NI.

3

Electric power is not supplied to C.B.

a) Disconnection of connector (CNDC)

3

Check connection of the connector 

(CNDC) on the C.B.

4

Disconnection of reactor (DCL)

4

Check connection of reactor. (DCL)

5

Defective power circuit board

5

Replace power circuit board.

6

Defective C.B.

6

Replace C.B. (When items above are 

checked but the units cannot be re-

paired).

7

Disconnection of wire between UNIT 

SIDE and MODULE SIDE.

7

Refer to 'How to remove the module'. 

Check connection of the wire between 

UNIT SIDE and MODULE SIDE.

F5

(5201)

63H connector open

Abnormal if 63H connector circuit 

is open for 3 minutes continuously 

after power supply.

63H: High pressure switch

1

Disconnection or contact failure of 63H 

connector on C.B.

1

Check connection of 63H connector on 

C.B.

2

Disconnection or contact failure of 63H

2

Check the 63H side of connecting wire.

3

63H is working due to defective parts.

3

Check continuity by tester.

Replace the parts if the parts are defec-

tive.

4

Defective C.B.

4

Replace C.B.

U1

(1302)

High pressure (High pressure 

switch 63H operated)

Abnormal if high pressure switch 

63H operated (4.15 MPa) during 

compressor operation.

63H: High pressure switch

1

Clogged or broken pipe

1

Check piping and repair defect.

2

Short cycle of refrigerant or ambient 

loop

2

-

3

 Check heat pump unit and repair defect.

3

Dirt of ambient loop heat exchanger

4

Decreased ambient loop flow rate

4

Check the ambient loop flow rate.

5

Disconnection or contact failure of 

connector (63H) on C.B.

5

-

7 

Turn the power off and check F5 is 

displayed when the power is turned 

again.

6

Disconnection or contact failure of 63H 

connection

7

Defective C.B.

8

Defective action of linear expansion 

valve

8

Check linear expansion valve.

RK79D203K01_01en.indd   48

2022/02/14   16:52:57

049

Содержание EHWT17D-MHEDW





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды