Mitsubishi Electric EHWT17D-MHEDW Скачать руководство пользователя страница 25

Страница: 25 / 60

4
5

Installation

4.6 Electrical Connection

All electrical work should be carried out by a suitably qualified

technician. Failure to comply with this could lead to electrocu-

tion, fire, and death. It will also invalidate product warranty. All

wiring should be according to national wiring regulations.

<FRONT>

<RIGHT SIDE>

Locally supplied wiring should be inserted through the inlets situ-

ated on the top of the heat pump unit. (Refer to <Table 3.3>.)

Wiring should be fed down the back right hand side of the

control and electrical box.

The wires should be inserted individually through the cable

inlets as below.

Connect the power cable for the immersion heater to ECB2.

The wires should be fixed with the cable straps as below

• Immersion heater cables should use the cable strap

• Output cables should use the cable strap

• Input cables, PICV power cables, and PICV output cables

should use the cable strap

• Power cables should use the cable strap

On completion of wiring ensure main remote controller cable

is connected to the relay connector.

* Before connecting the main remote controller cable, remove

the fastener bundling the cable between the power circuit

board and the relay connector.

Caution: Do NOT remove the band bundling the cable be-

tween the main remote controller and the relay connector, or

the heat pump unit may malfunction due to electrical noise of

the power circuit board. (See Figure 4.6.2.)

• Avoid contact between wiring and parts ( ).

• Make sure that ECB2 is ON.

• When connecting PICV, connect the terminal and PICV

Breaker

abbreviation

Meaning

ECB2

Earth leakage circuit breaker for immersion

heater

TB1

Terminal block 1

TB2

Terminal block 2

Connections should be made to the terminals indicated in the

figures.

Immersion heater should be connected independently from one

another to dedicated power supplies.

Main remote

controller

Outputs

ECB2

Inputs or

PICV outputs

TB2

TB1

Power circuit

board

Band

*Do NOT remove

Relay connector

Fastener

RK79D203K01_01en.indd 24

2022/02/14 16:52:50

025

Содержание EHWT17D-MHEDW





























































Результаты поиска

Содержание EHWT17D-MHEDW

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric EHWT17D-MHEDW, Руководство по установке

Результаты поиска

Содержание EHWT17D-MHEDW

Отзывы:

Бренды по названию

Популярные бренды