Mitsubishi Electric EHWT17D-MHEDW Скачать руководство пользователя страница 31

Страница: 31 / 60

System Set Up

5.1.4 2-zone valve ON/OFF control

Opening /closing 2-way valve provides a simple 2-Zone control.

Flow temperature is common for Zone1 and 2.

1. Pipe work

2. DIP switch

Turn DIP switch 3-6 ON.

3. 2-way valve 2a (for Zone1) / 2-way valve 2b (for Zone2)

Electrically wire 2-way valve 2a and 2b to the appropriate exter-

nal output terminals. (Refer to "External outputs" in 5.1.2)

4. Room thermostat connection

1. Zone1 2-way valve 2a (local supply)

2. Zone2 2-way valve 2b (local supply)

3. Water circulation pump 2 (local supply) *1

4. By-pass valve (local supply) *2

*1 Install according to system in the field.

*2 For safety protection, it is recommended to

install a auto-operational (eg. mechanical spring

ie. not manual valve) by-pass valve.

Note:

Freeze stat function is deactivated whilst this con-

trol is ON. Use anti-freeze solution to avoid freez-

ing, if necessary.

Heating operation mode

Zone1

Zone2

Room temp. control

(Auto adaptation) *3

● Wireless remote controller (option)

● Room temperature thermistor (option)

● Main remote controller (remote position)

● Wireless remote controller (option)

Compensation curve or flow temp. control ● Wireless remote controller (option) *4

● Room temperature thermostat (local supply)

● Wireless remote controller (option) *4

●

Room temperature thermostat (local supply)

*3 Ensure to install the room thermostat for Zone1 in main room since the Room temp. control for Zone1 is prioritized.

*4 The wireless remote controller can be used as a thermostat.

Zone1

Zone2

N L

FTC

TBO.2

1 2 3

5.1.3 Wiring for 2-zone temperature control

Connect the pipe work and locally supplied parts according to

the relevant circuit diagram shown “Local system” in Section 3,

of this manual.

Connect the signal line to open Port A (hot water inlet port) to

TBO. 2-3 (Open), the signal line to open Port B (cold water

inlet port) to TBO. 2-1 (Close) , and the neutral terminal wire

to TBO. 2-2 (N).

• Do not install the thermistors on the mixing tank.

•

Install the Zone2 flow temp. thermistor (THW8) near the mix

ing valve.

• The maximum length of the thermistor wiring is 30 m.

• The length of the optional thermistors are 5 m. If you need to

splice and extend the wirings, following points must be car-

ried out.

1) Connect the wirings by soldering.

2) Insulate each connecting point against dust and water.

Note:

Do not install the thermistors on the mixing tank. This

could affect correct monitoring of flow and return tempera

tures through each zone.

Install the Zone2 flow temp. thermistor (THW8) near the

mixing valve.

Close N Open

from mixing

tank

to mixing

tank

to Zone2

heat emitter

from Zone2

heat emitter

Motorized

mixing valve

RK79D203K01_01en.indd 30

2022/02/14 16:52:51

031

Содержание EHWT17D-MHEDW





























































Результаты поиска

Содержание EHWT17D-MHEDW

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric EHWT17D-MHEDW, Руководство по установке

Результаты поиска

Содержание EHWT17D-MHEDW

Отзывы:

Бренды по названию

Популярные бренды