Mitsubishi Electric ecodan PUHZ-W50VHA2 Скачать руководство пользователя страница 52

Страница: 52 / 60

PUHZ-W50VHA2R1 PUHZ-W50VHA2R1-BS

1. Removing the service panel and top panel

(1) Remove 3 screws (5

12) and slide the hook on the right

downward to remove the service panel.

(2) Remove screws (3 for front, 3 for rear/5

12) of the top

panel and remove it.

Note: When removing service panel and top panel at the

same time, count one less screw since they share a

screw.

2. Removing the fan motor (MF1)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove 5 screws (5

12) to detach the fan grille.

(See Photo 1)

(4) Remove a nut (for right handed screw of M6) to detach the

propeller. (See Photo 2)

(5) Disconnect the connector CNF1 (WH) on controller circuit

board in electrical parts box. (See Photo 4)

(6) Loosen the clamp for the lead wire on motor support and

separator. (See Photo 4)

(7) Release the lead wire from the hole on separator.

(See Photo 4)

(8) Remove 4 screws (5

20) to detach the fan motor.

(See Photo 3)

Photo 2

Propeller

Front panel

Front panel fixing screws

Nut

Fan motor fixing screws

Clamp

Fan

motor

(MF1)

Fan motor

fixing screws

Photo 3

3. Removing the electrical box

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Disconnect the connecting wires from terminal block.

(4) Remove all the following connectors from controller circuit board;

CNF1 (WH). LEV-A (WH), LEV-B (RD), TH3 (WH). TH4 (WH), TH7/6

(RD), TH32 (BK), TH34 (RD), 63HS (WH), 63H (YE) and 21S4 (GN).

Pull out the disconnected wire from the electrical parts box.

• Fan motor (CNF1)

• Linear Expansion Valve (LEV-A and LEV-B)

• Thermistor <Liquid> (TH3)

• Thermistor <Discharge> (TH4)

• Thermistor <Ambient/Plate HEX Liquid> (TH7/6)

• Thermistor <Inlet Water> (TH32)

• Thermistor <Comp. Surface> (TH34)

• High Pressure Sensor (63HS)

• High Pressure Switch (63H)

• Solenoid Valve Coil <4-way valve> (21S4)

(5) Loosen the clamps, fasteners and cable strap for the lead

wire in the electrical parts box and separator.

(6) Loosen the lead wire fixed to the pipes with bands.

(7) Remove the damper top.

(8) Remove the flange nut and terminal cover, then disconnect

the compressor lead wires.

(9) Remove 2 screws (4

10) and detach the electrical parts

box by pulling it upward. The electrical parts box is fixed

with 2 hooks on the left and 1 hook on the right.

Photo 4

Electrical parts box

Electrical

parts box

fixing screws

(4 × 10)

Controller circuit board (C.B.)

Photo 1

Top panel fixing screws

Top panel

Service panel

fixing screws

Service panel

Grille fixing screws

Cover panel

(front)

Cover panel

front fixing screws

Fan grille

Slide

Side panel (R)

Valve bed

fixing screw

(4 × 8)

Terminal cover

Terminal

block

Separator

Clamps

Motor support

Valve bed

fixing screws

(4 × 8)

Damper top

OPERATING PROCEDURE

PHOTOS

OCH605A

Содержание ecodan PUHZ-W50VHA2





























































Результаты поиска

Содержание ecodan PUHZ-W50VHA2

Отзывы:

Похожие инструкции для ecodan PUHZ-W50VHA2

Бренды по названию

Популярные бренды

Mitsubishi Electric ecodan PUHZ-W50VHA2, Руководство по обслуживанию

Результаты поиска

Содержание ecodan PUHZ-W50VHA2

Отзывы:

Похожие инструкции для ecodan PUHZ-W50VHA2

Бренды по названию

Популярные бренды