background image

EN-6

Preparing your projector

1

2

3

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in 
the package. 

Important:

•  The attached power cords are to be used exclusively for this product. Never use them for other products.

Inserting the batteries into the remote control

1.  Remove the rear lid of the remote control.
2.  Check the polarity (+), (-) of the batteries, and set them 

correctly, inserting their (-) side fi rst.
•  If the battery is inserted from the (+) side fi rst, inserting 

the (-) side is diffi cult because the coil spring end hits on 
the battery side. If the battery is forced to insert in this 
way, the outer label of the battery may get ripped and it 
may cause a short-circuit and heating.

3.  Attach the rear lid.

Important:

•  Use two size-AA batteries (R6).
•  Replace the 2 batteries with new ones when the remote 

control is slow to operate.

CAUTION: 

•  Use of a battery of wrong type may cause explosion.  
•  Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used. 
•  Dispose of used batteries according to your local regulations. 
•  Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fi re.
•  Be sure to handle the batteries according to the instructions.  
•  Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control. 
•  Keep batteries out of reach of children and pets. 
•  Remove the batteries, if the remote control is not used for a long time. 
•  Do not combine a new battery with an old one.
•  If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in 

contact with your eyes, rinse them with water and then consult your doctor.

Cables

Power supply parts

Remote control parts

Power cord 

(two)

(246C483-10, 246C383-20)

Remote control

(290P136-20)

R6 (size-AA) 
battery (two) 

RS-232C cable

(246C548-10)

RGB cable for PC 

(246C521-10)

USB cable

(246C509-10)

Audio/Video cable

(246C381-10)

Others

• Lens cap (Attached to the 

projector)

• Terminal cover (750A561-10)
• Quick Start up (857D079-10)
• CD-ROM (919C151-10)
• Safety manual (871D468-10)

Mini D-SUB

15-pin

Mini D-SUB

15-pin

D-SUB 9-pin

•  Used for projector control 

by computer.

USB 4

-pin

(type B)

USB 4

-pin

(type A)

D-SUB 9-pin

Remote control
cable
  (246C424-10)

Содержание DLP XD1000U










































Отзывы: