Mitsubishi Electric CITY MULTI PLFY-P VFM-E1 Series, Руководство по эксплуатации

Страница: 11 / 232

11
GB
2SHUDWLRQ
'L6HHVHQVRUVHWWLQJ
'L6HHVHQVRUVHWWLQJ
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Maintenance
Initial setting
Service
1 Select “Maintenance” from the
Main menu (refer to page 8), and
press the [SELECT] button.
Ŷ
0DQXDOYDQHDQJOH:LUHOHVVUHPRWHFRQWUROOHU
)LJ
A
)LJ
B
)LJ
1 Going to the Manual vane setting
mode
Press the button.
(Start this operation from the
status of remote controller
display turned off.)
“FUNCTION” is lighted and “1”
blinks. (Fig. 3-1)
Press the button to select “2”,
and then press the button.
2 Selecting the vane number (Fig.
3-2)
Press the buttons to select
the vane number A , and then
press the button.
3
Setting the vane angle (Fig. 3-3)
Press the buttons to select
the vane angle
B
.
Point the wireless remote
controller toward the receiver on
the indoor unit, and then press
the
button.
4
Press the button to
complete the settings.
Display
Setting Step 1 Step 2 Step 3 Step 4
Display No display
Setting Step 5 No setting Draft reduction*
F1 F2 F3 F4
Maintenance menu
Main menu:
Cursor
Auto descending panel
Manual vane angle
3D i-See sensor
F1 F2 F3 F4
3D i-See sensor
Cursor
Setting display:
Air distribution
Energy saving option
Seasonal airflow
$LUGLVWULEXWLRQ
F1 F2 F3 F4
Air distribution
Input display:
Address Check
M-NET address
Identify unit Check button
F1 F2 F3 F4
Air distribution
Select:
Cur.
M-NET address
Auto vane
Direct/Indirect setting
Direct/Indirect
Vane setting
Direct Indirect
Cooling
horizontal ĺ swing keep horizontal
Heating keep downward downward ĺ horizontal
2
Select “3D i-See sensor” with the
[F1] or [F2] button, and press the
[SELECT] button.
3
Select the desired menu with the
[F1] or [F2] button, and press the
[SELECT] button.
• Air distribution
Select the airflow direction control
method when the airflow direction
is set to “Auto”.
• Energy saving option
Operates the energy-save mode
according to whether persons are
detected in the room by the 3D
i-See sensor.
• Seasonal airflow
When the thermostat turns off,
the fan and the vanes operate
according to the control settings.
1 Select the M-NET address for the
units to whose vanes are to be
fixed, with the [F2] or [F3] button,
and press the [SELECT] button.
Press the [F4] button to confirm the
unit.
The vane of only the target indoor
unit is pointing downward.
2
Select the menu with the [F4]
button.
Default ĺ Area ĺ Direct/Indirect
ĺ Default «
Default: The vanes move the same
as during normal operation.
During cooling mode, all of the
vanes move to the horizontal
airflow direction.
During heating mode, all of the
vanes move to the down airflow
direction.
Area: The vanes move to the
down airflow direction toward
areas with a high floor temperature
during cooling mode and toward
areas with a low floor temperature
during heating mode. Otherwise,
the vanes move to the horizontal
airflow direction.
D i r e c t / I n d i r e c t : T h e v a n e s
automatically move relative to the
areas where persons are detected.
The vanes operate as indicated in
the following table.
* The draft reduction can be set for only 1 vane.
The setting is enabled only for the last vane that was set.