Mitsubishi Electric CITY MULTI PLFY-P VFM-E1 Series, Руководство по эксплуатации, Страница: 10 / 232

10
GB
2SHUDWLRQ
Ŷ
0DQXDOYDQHDQJOH:LUHGUHPRWHFRQWUROOHU
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Maintenance
Initial setting
Service
F1 F2 F3 F4
Maintenance menu
Main menu:
Cursor
Auto descending panel
Manual vane angle
3D i-See sensor
F1 F2 F3 F4
Manual vane angle
Input display:
Address Check
M-NET address
Identify unit Check button
1
F1 F2 F3 F4
Manual vane angle
Manual vane angle
Select:
Setting
Outlet Angle
Note:
Do not set the draft reduction in an environment with high humidity.
Otherwise, condensation may form and drip.
1 Select “Maintenance” from the
Main menu (refer to page 8), and
press the [SELECT] button.
2 Select “Manual vane angle” with
the [F1] or [F2] button, and press
the [SELECT] button.
3 Select the “M-NET address” for
the units to whose vanes are to be
fixed, with the [F2] or [F3] button,
and press the [SELECT] button.
Press the [F4] button to confirm the
unit.
The vane of only the target indoor
unit is pointing downward.
4 The current vane setting will
appear.
Select the desired outlets from
1 through 4 with the [F1] or [F2]
button.
• Outlet: “1”, “2”, “3”, “4” and “1, 2, 3,
4, (all outlets)”
Press the [F3] or [F4] button to go
through the option in the order of
“No setting (reset)”, “Step 1”, “Step
2”, “Step 3”, “Step 4”, “Step 5” and
“Draft reduction*”.
Select the desired setting.
* Draft reduction
The airflow direction for this setting
is more horizontal than the airflow
direction for the “Step 1” setting in
order to reduce a drafty feeling.
The draft reduction can be set for
only 1 vane.
Ŷ
Vane setting
No setting Step 1 Step 2
Step 4 Step 3
All
outlets Draft
reduction*
Step 5
Press the [SELECT] button to save the settings.
A screen will appear that indicates the setting information is being trans-
mitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above (step 5)
when the transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected, will be displayed the next time
the unit goes into operation.
Navigating through the screens
• To go back to the Main menu ................ [MENU] button
• To return to the previous screen .......... [RETURN] button
Ŷ
&RQ¿UPDWLRQSURFHGXUH
F1 F2 F3 F4
1
Manual vane angle
Input display:
Address Check
M-NET address
Identify unit Check button
F1 F2 F3 F4
Manual vane angle
Return:
M-NET address
Function setting for unit
with vane fully open.
F1 F2 F3 F4
Manual vane angle
Return:
No communication
Check Unit state.
Caution:
To prevent falls, maintain a stable footing when operating the unit.
1 Select the “M-NET address” for
the units to whose vanes are to be
fixed, with the [F2] or [F3] button.
Press the [F4] button to con
¿ rm the
unit.
2 After pressing the [F4] button, wait
approximately 15 seconds, and
then check the current state of the
air conditioner.
ĺ The vane is pointing downward.
ĺ This air conditioner is displayed
on the remote controller.
ĺ All outlets are closed. ĺ Press
the [RETURN] button and continue
the operation from the beginning.
ĺ The messages shown to the left
are displayed. ĺ The target device
does not exist at this refrigerant
address.
• Press the [RETURN] button to
return to the initial screen.
3 Change the “M-NET address” to
the next number.
• Refer to step 1 to change the
“M-NET address” and continue
with the confirmation.