Mitel DBC 223 Скачать руководство пользователя страница 58

Страница: 58 / 121

3/1553-ANF 901 54 Uen F5 2018-12-03

URING

CALLS

5.7.1

TRANSFER AFTER ANSWER

•

Make an inquiry call (press the soft-key

Conf/Transf

or the Inquiry-key and wait

for dial tone).

•

Dial the extension or external number and wait for answer.

•

Announce the call.

•

Press the soft-key

Transfer

5.7.2

TRANSFER BEFORE ANSWER

•

Make an inquiry call (press the soft-key

Conf/Transf

or the Inquiry-key and wait

for dial tone).

•

Dial the extension or external number and wait for ringing tone.

•

Press the soft-key

Transfer

Note:

If the wanted extension is busy or transfer to this extension is forbidden the

transfer will not be performed.

5.8

DISPLAY OF CHARGING

This function allows you to have the cost of a call (charged external connection) shown

in the display while the call is connected. The cost information in the display is contin

uously updated during the connection, if the exchange supports this function.
The following is an example of display information when the telephone is in speech with

an external subscriber and the feature display of charging information is active.

5.8.1

TO ACTIVATE DISPLAY OF CHARGING INFORMATION

The feature display of charging information can be activated while in speech.
•

Press the soft-key

CostInfo

The cost information is shown in the first row in the display after a short delay. If the

feature is activated, the cost information will be automatically displayed for all charged

calls. That is, you do not need to press the soft-key for each connection.

5.8.2

TO DEACTIVATE DISPLAY OF CHARGING INFORMATION

The feature display of charging information can be deactivated while in speech.
•

Press the soft-key

CostInfo

Содержание DBC 223


























































































































Результаты поиска

Содержание DBC 223

Отзывы:

Бренды по названию

Популярные бренды

Mitel DBC 223, Инструкция по применению

Результаты поиска

Содержание DBC 223

Отзывы:

Бренды по названию

Популярные бренды