Mitel DBC 223 Скачать руководство пользователя страница 110

Страница: 110 / 121

3/1553-ANF 901 54 Uen F5 2018-12-03

110

ISCELLANEOUS

11.5.3

TO CHANGE FROM HANDSET TO HEADSET MODE

•

Press the Headset-key.

•

Replace the handset.

11.5.4

TO CHANGE FROM HEADSET MODE TO LOUDSPEAKING WITH

HEADSET

•

Press the Speaker-key.

11.5.5

TO CHANGE FROM LOUDSPEAKING WITH HEADSET TO HEADSET

MODE

•

Press the Speaker-key.

11.5.6

TO CHANGE FROM HEADSET MODE TO HANDSFREE

•

Press the Speaker-key.

•

Press the Headset-key.

11.5.7

TO CHANGE FROM HANDSFREE TO HEADSET MODE

•

Press the Headset-key.

11.5.8

TO CLEAR THE CALL

•

Press the Clear-key.

11.6

HEADSET PRESET FUNCTION

Headset Preset

By default the telephone is set for calls to be connected to the loudspeaker when you

answer or make calls by pressing a Line key, so called Loudspeaker Preset. Also when

you dial the number without lifting the handset, the call is automatically connected to

the loudspeaker.
When you use a headset for your telephone, you can change the setting to get calls

connected to the headset instead, so called Headset Preset.

Note:

Independently of the type of preset setting, when you lift the handset the call is

always connected to the handset.

Also handsfree and loudspeaking work as usual, that is, when the Loud

speaker key is pressed, the call is temporarily connected to the loudspeaker.
Activation and cancellation of Headset Preset can only be done when the tele

phone is in idle mode.

Headset Preset can be activated and canceled either by use of the headset and loud

speaker keys, or via the soft-key

PhoneSet

To activate using the soft-key PhoneSet:

•

Press the soft-key

PhoneSet

Содержание DBC 223


























































































































Результаты поиска

Содержание DBC 223

Отзывы:

Бренды по названию

Популярные бренды

Mitel DBC 223, Инструкция по применению

Результаты поиска

Содержание DBC 223

Отзывы:

Бренды по названию

Популярные бренды