Mipex MIPEX-02 Series Скачать руководство пользователя страница 7

Страница: 7 / 46

Optosense LLC

USER MANUAL

Design department

SMALL-SIZE EXPLOSIVE GAS MEASURING

SENSOR MIPEX-02-X-X-X.1 X (RX)

ESAT.413347.005 UM

Revision 3.0

January 19th, 2017

Page 7 of 46

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED.

3. TECHNICAL SPECIFICATIONS

Table 2. General specifications (for available options see Appendix A)

Gas sampling method

Diffusion

Operating principle

Non-Dispersive Infra-Red (NDIR)

Target gas

/CH

+С

Operating,

storage and

transportation

conditions:

Relative humidity, %

up to 98

Atmospheric pressure, kPa

80…120

Temperature

, °C

-55...+60

Temperature range

, °C

10…+40

40…+60

20…+50

Overall dimensions, mm

⌀

20.2×16.6 (without pins; housing types “1” and “3”)

⌀

22×16.6 (without pins; housing type “2”)

Pins length, mm

4.6

5.75

Warm-up time, sec

≤ 120

Weight, g

16.6 (

housing type “1”)

15.5 (

housing type “2”)

5.5 (

housing type “3”)

Housing material

Stainless steel (

housing types “1” and “2”)

Plastic

Lexan™ (housing type “3”)

Life time expectancy

(not less than), years

Shelf life time (not less than), years

IP rating

20 (without dust filter)

54 (if a dust filter provided by Optosense LLC is
applied)

See Appendix A for details.

Term “operating temperature” refers to ambient temperature, at which sensor operates and its

intrinsic safety is ensured, but sensor readings variability stated in Table 3 is provided only in specified
temperature range (see Table 5 and Table 6).

For information on housing types, see Appendix A.

To provide metrological properties during sensor lifetime, zeroing and span calibration should be

performed periodically, at least once in 30 months (see Appendix D.1).

Содержание MIPEX-02 Series















































Результаты поиска

Содержание MIPEX-02 Series

Отзывы:

Mipex MIPEX-02 Series, Руководство пользователя, Страница: 7 / 46

Результаты поиска

Содержание MIPEX-02 Series

Отзывы: