Minolta CF910 Скачать руководство пользователя

Страница: 15 / 206

1-1

ty No

tes

Chapter 1

1. Installing the Copier

Installation Site

To ensure utmost safety and prevent possible malfunctions of the copier, install it in a location which
meets the following requirements.

Power Source

The power source voltage requirements are as follows.

◆

Use a power source with little voltage fluctuation.

Voltage Fluctuation

Within ± 10%

Frequency Fluctuation

Within ± 0.3%

Space Requirements

To ensure easy copier operation, supply replacements and service maintenance, adhere to the
recommended space requirements detailed below.
* Be sure to allow a clearance of 6” or more at the back of the copier as there is a ventilation duct.

◆

A place away from a curtain or the like that may
catch fire and burn easily.

◆

An area where there is no possibility of being
splashed with water or other types of liquid.

◆

An area free from direct sunlight.

◆

A place out of the direct air stream of an air
conditioner, heater, or ventilator.

◆

A well-ventilated place.

◆

A dry place.

◆

A dust-free location.

◆

An area not subject to undue vibration.

◆

A stable and level location.

◆

A place where ammonia or other organic gas is
not generated.

◆

A place which does not put the operator in the
direct stream of exhaust from the copier.

◆

A place which is not near any kind of heating
device.

1154O026AA

Scale: inch

60-3/4

24-1/2

36-1/4

42-3/4

25-1/4

50-1/4

Содержание CF910















































































































































































































Результаты поиска

Содержание CF910

Отзывы:

Похожие инструкции для CF910

Бренды по названию

Популярные бренды

Minolta CF910, Руководство оператора

Результаты поиска

Содержание CF910

Отзывы:

Похожие инструкции для CF910

Бренды по названию

Популярные бренды