Minnich Hornet 24/22, Руководство оператора и по обслуживанию

Страница: 7 / 25

7
Dowel Drill Manual
GENERAL SAFETY
∆ ALWAYS keep the machine in proper running
condition.
∆ ALWAYS become familiar with the compo-
nents of the machine before operation.
∆ Fix damage to machine and replace any bro-
ken parts immediately.
∆ ALWAYS store equipment properly when it is
not being used. Equipment should be stored
in a clean, dry location out of the reach of
children and unauthorized personnel.
∆ NEVER lubricate components or attempt ser-
vice on a running machine
∆ NEVER tamper with the factory
settings of the engine or en-
gine governor. Damage to the
engine or equipment can result
in operation in speed ranges
above the maximum allowabil-
ity.
∆ ALWAYS Dispose of hazardous waste proper-
ly. Examples of potentially hazardous waste
include used motor oil, fuel, and fuel filters.
∆ DO NOT use food or plastic containers to
dispose hazardous waste.
∆ DO NOT pour waste or oil directly onto the
ground, down or drain or into any waste
source.
WARNING
NOISE MAY
DAMAGE HEARING
WEAR PROPER HEARING
PROTECTION
FLYING PARTICLES MAY CAUSE
EYE INJURIES
WEAR PROPER EYE
PROTECTION
HIGH PRESSURE
KEEP AWAY FROM LEAKS
BLEED DOWN BEFORE REMOVING
LINES TO SERVICE
DUST CAN CAUSE INJURY TO
YOUR HEALTH
IF VENTILATION IS INADEQUATE
USE AN APPROVED RESPIRATOR
12287- 3
DRILLS WILL
AUTOMATICALLY START
WHEN AIR SUPPLY IS LOST
AND REAPPLIED
12287-64
WARNING
WARNING
BE SURE SUPPLY LINES ARE SECURE
DO NOT EXCEED 120 PSI (8.25 BARS)
OR DAMAGE TO MACHINE AND OR
BODILY HARM MAY RESULT
12287-1
INSTALL LOCK
PIN PRIOR TO
TRANSPORTING MACHINE
12287-7
INSTALL LOCK
PIN PRIOR TO
TRANSPORTING MACHINE
12287-7
INSTALL LOCK
PIN PRIOR TO
TRANSPORTING MACHINE
12287-7
WARNING
KEEP GUARDS IN PLACE
DISCONNECT POWER
BEFORE SERVICING
12287-12
WARNING
KEEP GUARDS IN PLACE
DISCONNECT POWER
BEFORE SERVICING
12287-12
12287-62 12287-62
12287-62 12287-62
X
X X
X
DRILLS
FEED
1
2
ON
ON
OFF
OFF
IN
IN
OUT
OUT
TM
WARNING
STAND CLEAR
WHEN RAISING OR LOWERING
12287-10
12287-43
READ & UNDERSTAND OWNERS MANUAL COMPLETELY.
TIGHTEN ALL LOOSE BOLTS INSPECT ALL LINES, PIPES, AND HOSES FOR DAMAGE.
REPAIR AS NECESSARY.
DRILL STEEL MUST NOT BE BINDING IN GUIDE BEARING. MAKE SURE DRILL STEEL
IS STRAIGHT, FREE OF OBSTRUCTIONS, AND NOT BINDING IN ANYWAY.
FILL THE OILER-PER MANUAL.
WARNING
STAND CLEAR
WHEN RAISING OR LOWERING
12287-10
Bio-Rock Drill Oil 15W50
TM
Minnich Mfg. Recommended Rock Drill Oil
A-2-BW
A-2-BW
BEFORE CONNECTING THE AIR COMPRESSOR:
∆ NEVER attempt to loosen any compressed air
hose that is pressurized.
∆ KEEP AWAY from all hot or spark generating
objects, do not smoke when handling fuel.
∆ So as to facilitate shipment, new or repaired
units are not lubricated before delivery to cus-
tomers.
∆ DO NOT use hydrocarbons and especially do
not use fuel oil for lubricating purposes.
∆ DO NOT OPERATE MACHINE WITHOUT
GUARDS AND COVERS IN PLACE
∆ ALWAYS disconnect the air supply before chang-
ing steel or dismantling the tool for service or
repair. For maximum safety we advise the in-
stallation of a shut-off valve at the end of the air
line.
∆ NEVER operate the engine with heat shields or
guards removed.
∆ DO NOT remove the engine oil drain plug while
the engine is hot. Hot oil will gush out of the
engine crankcase and severely scald any persons
in the general area of the machine.
∆ Install the drill steel and bits into the drill motors
and close the latch retainers and rod guides.
∆ Make sure that the air compressor is set at an
operating pressure of not more than 120 PSIG
(8Bar)
∆ Make sure air line is cleaned out and is of the
proper size and pressure rating for the drill unit.
∆ Make sure the lubricator is filled with proper
lubricant. See Minnich recommended lubricant
below.
∆ Make sure all controls are in the “off” position
and the lift lever (if so equipped) is in the “up”
position.
∆ Make sure all lock pins are in their locked posi-
tion.