background image

3

Dowel Drill 

Manual

     

GENERAL

 

WARNINGS

CALIFORNIA PROPOSITION 65

Engine exhaust and some of its constituents, 

and some dust created by power sanding, 

sawing, grinding, drilling and other construction 

activities contains chemicals known to the Sate 

of California to cause cancer, birth defects and 

other reproductive harm. Some examples of 

these chemicals are:

Lead from lead-based paints.

Crystalline silica from bricks.

Arsenic and chromium from chemically treated 

lumbar.

Your risk from these exposures caries, depend-

ing on how often you do this type of work. To 

reduce your exposure to these chemicals:

ALWAYS work in a well ventilated area, and 

work with improved safety equipment, such 

as dust masks that are specifically designed to 

filter out microscopic particles.

SILICOSIS WARNING

Grinding/cutting/drilling of masonry, concrete,-

metal and other materials with silica in their 

composition may give off dust or mist contain-

ing crystalline silica.  

Silica is a basic components of sand, quarts, 

brick clay, granite and numerous other minerals 

and rocks. Repeated and/or substantial inha-

lation of airborne crystalline silica can cause 

serious or fatal respirator disease, including sil-

icosis. In addition, California and some author-

ities have listed repairable crystalline silica as a 

substance known to cause cancer. When cutting 

such materials, always follow the respiratory 

precautions mentioned above.

RESPIRATORY HAZARDS
 

  Grinding/cutting/drilling of masonry, concrete,metal and fumes containing 

chemicals known to cause serious or fatal injury or illness, such as respirato-

ry disease, cancer, birth defects or other reproduction harm, if you are 

unfamiliar with th risks associated with the particular process and/or materi-

al being cut or the composition of the tool being used, review the material 

safety data sher and/or consult your employer, the material manufacturer/

supplier, governmental agencies such as OSHA and NIOSH and other 

sources on hazardous materials. California and some other authorities, for 

instance, have published lists of substances known to cause cancer, repro-

ductive toxicity or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and 

follow the recommendations of the manufactures of suppliers, OSHA/NIOSH, and occupational and 

trade associations. Water should be used for dust suppression when wet cutting is feasible. When the 

hazards from inhalation of dust, mist and fumes cannot be eliminated, the operator and any bystand-

ers should always wear a respirator approved by NIOSH/MSHA for the materials being used.

Содержание Hornet 24/22


























Отзывы: