MINN KOTA Riptide Ulterra Скачать руководство пользователя

Страница: 30 / 48

32 | minnkotamotors.com

TRACK RECORDIng / PLAYbACK

REPLAYIng A TRACK
(TRACK TO sTART / TRACK TO EnD)

1. Manually navigate the boat to within a quarter mile of the saved track. Due to safety reasons, i-Pilot will not re-engage a saved track

greater than a quarter mile away.

2. Press

on the remote.

3. The Memory Location icon will fl ash on the remote LCD for three seconds, allowing you to choose a

memory location by pressing

. Pressing the button pressed in step 2 again or waiting for

three seconds accepts the memory location.

4. Adjust motor speed to desired setting to engage and navigate track automatically.

RECORD, TRACK TO EnD AnD TRACK TO sTART EsCAPE

1. If

is accidentally hit, press

within three seconds on the remote to cancel the command.

fOOT PEDAL OPERATIOn

• Steering left or right or turning

Advanced AutoPilot

on with the foot pedal will disengage

Track to Start

Track to End

You can switch directly between Track to Start and

Track to End. This allows you to concentrate on

productive sections of a track.

i-Pilot TIPS

SYSTEM READY

POWER

STATUS

In the unlikely event Ulterra will not trim or stow, the following procedure will reset the motor and restore functionality:

1. Press and hold the POWER button located at the

mounting base to turn power off (green LED light will
turn off ).

2. Press the POWER button until the green LED light

illuminates.

3. Wait 3 seconds.

4. Press the POWER button 3 times within a 2 second

period.

5. Red and green LED lights will fl ash continuously and

the Ulterra will go through the following automated
sequence:

• Motor will position itself into the proper orientation

• Motor will automatically trim up to the mounting base and trim down approximately 6 inches.

• The fl ashing red LED light will turn off , and the fl ashing green LED light will become solid green.

Ulterra is now reset and fully functional.

If Ulterra does not reset, repeat the procedure. If the second attempt fails, please contact your local authorized service center or call
Minn Kota service at (800) 227-6433.

NOTE:

If the lower unit of the motor is trimmed within 6 inches of the mounting base and the boat hull is obstructing the motor’s

turning radius, manually turn the head of the motor so that the lower unit is perpendicular to the motor ramps prior to beginning this
procedure.

30 | minnkotamotors.com

Содержание Riptide Ulterra

















































Результаты поиска

Содержание Riptide Ulterra

Отзывы:

Похожие инструкции для Riptide Ulterra

Бренды по названию

Популярные бренды

MINN KOTA Riptide Ulterra, Руководство пользователя

Результаты поиска

Содержание Riptide Ulterra

Отзывы:

Похожие инструкции для Riptide Ulterra

Бренды по названию

Популярные бренды