MINN KOTA Riptide Ulterra Скачать руководство пользователя

Страница: 18 / 48

18 | minnkotamotors.com

gETTIng sTARTED

AUDIO mODEs

The i-Pilot Controller also contains an internal speaker which can be programmed to work in two diff erent audio modes. The speaker is
programmed to operate in audio mode one from the factory. To enable diff erent audio modes hold

and

down at the same

time for three seconds. For an explanation of each audio mode and their sounds see the table below.

WHAT COnDITIOn CAUsEs IT

AUDIO mODE

AUDIO PATTERn

Startup

Modes 1 and 2

4 Short beeps

Manual prop on

Mode 2

Single beep

Manual prop off

Mode 2

Double beep

Speed + (when less than max speed)

Mode 2

Single beep

Speed - (when greater than speed 0)

Mode 2

Single beep

High Speed Bypass enable

Mode 2

Single beep

High Speed Bypass disable

Mode 2

Double beep

Button press for any of these (enable or

disable): REC, Pause, Track to Start, Track

to End, AutoPilot, Cruise Control,

Spot-Lock, Spot-Lock Recall

Mode 2

Single beep

Moving more than a quarter mile from

the last track point while in Record Pause

mode

Mode 2

Error

When GPS Signal Strength goes to no

bars while in a GPS-based mode

Mode 2

Error

Attempting to enable a GPS feature when

no signal strength bars are shown

Mode 2

Error

Attempting to replay a Track or recall

a Spot-Lock location when the boat is

beyond the minimum distance

Mode 2

Error

MOM button on the footpedal is pressed

and a remote button press attempts to

override it

Mode 2

Error

End of track attained during track playback

(in conjunction with cancelling mode and

turning the prop off )

Mode 2

High-Low,

High-Low

Switch to Audio Mode 1

Modes 1 and 2

Single beep

Switch to Audio Mode 2

Modes 1 and 2

Double beep

Learn button is pressed

Modes 1 and 2

Steady tone

Learn successfully completed

Modes 1 and 2

3 longer beeps

Initiating a command that is not allowed in

the prop lockout region

Mode 2

Error

Deploy

Mode 2

Double beep

Stow

Mode 2

Single beep

Initiating a command that is not allowed in

the stow/deploy process

Mode 2

Error

Current Limit

Mode 2

High-Low

20 | minnkotamotors.com

gETTIng sTARTED

Содержание Riptide Ulterra

















































Результаты поиска

Содержание Riptide Ulterra

Отзывы:

Похожие инструкции для Riptide Ulterra

Бренды по названию

Популярные бренды

MINN KOTA Riptide Ulterra, Руководство пользователя

Результаты поиска

Содержание Riptide Ulterra

Отзывы:

Похожие инструкции для Riptide Ulterra

Бренды по названию

Популярные бренды