MiniMag 17'' DISK PAD ASSIST Скачать руководство пользователя страница 35

Страница: 35 / 44

INI

-OP-EN

- 35 -

MACHINE SPECS

BODY CONSTRUCTION/DIMENSIONS

INI

(PAD ASSIST)

INI

(TRACTION)

TANK MATERIAL:

POLY (

⁄

'') (.9525 cm)

POLY (

⁄

'') (.9525 cm)

CHASSIS CONSTRUCTION:

⁄

'' STEEL (.2 cm)

⁄

'' STEEL (.2 cm)

FRONT WHEELS:

) 9''

2'' [(2

) 23

5 cm]

) 9''

3'' [(2

) 23

8 cm]

REAR CASTERS:

) 4''

2'' [(2

) 10

5 cm]

) 4''

2'' [(2

) 10

5 cm]

SIZE (L × W × H):

45''

18''

40'' (114

102 cm)

45''

18''

40'' (114

102 cm)

WEIGHT (WITHOUT BATTERIES):

242 LB.

152 LB.

WEIGHT (WITH BATTERIES):

374 LB.

387 LB.

SCRUBDECK SYSTEM

DISK BRUSH SIZE:

17-D: (1

) 17'' (43 cm)

20-D: (1

) 20'' (51 cm)

23-D: (1

) 23'' (59 cm)

17-D: (1

) 17'' (43 cm)

20-D: (1

) 20'' (51 cm)

23-D: (1

) 20'' (51 cm)

26-D: (1

) 20'' (51 cm)

28-D: (1

) 20'' (51 cm)

DISK SCRUBDECK MOTOR:

) .75 HP (559 watts) / 200 RPM (1

) .75 HP (559 watts) / 200 RPM

OPTIONAL SCRUBDECK MOTOR:

) 1 HP (746 watts) / 200 RPM

CYLINDRICAL BRUSH SIZE:

) 22''

5.5''

CYLINDRICAL SCRUBDECK MOTOR:

) .75 HP (559 watts) / 750 RPM

EDGE PAD SIZE:

N / A

20-E: (1

) 20''

14''

24-E: (1

) 24''

14''

28-E: (1

) 28''

14''

EDGE SCRUBDECK MOTOR:

N / A

) 1.2 HP (895 watts) / 2900

RPM

SCRUBDECK DOWN PRESSURE:

0-125 LB (0-57 kg)

0-150 LB (0-68 kg)

SOLUTION SYSTEM

SOL. TANK CAPACITY:

17 GAL (64 liters)

SOLUTION FLOW RATE:

0 - 1.0 GPM (0 - 4 lpm)

SOLUTION FILTER:

STAINLESS / INLINE

RECOVERY SYSTEM

REC. TANK CAPACITY:

17 GAL (64 liters)

VACUUM POWER:

0.75 HP (559 watts)

DRAIN HOSE:

1.5'' DIAMETER (4 cm)

VACUUM SPECS (LIFT / AIRFLOW):

70'' / 70 cfm (178 cm / 21cmm)

DEMISTING CHAMBER:

1.25 GAL (5 liters)

DRAIN SAVER:

30 in

(70 cm

)

30 in

(70 cm

)

BATTERY SYSTEM

SYSTEM VOLTAGE:

24 VOLTS

STANDARD BATTERY AH RATING:

(2×) 130 AH

(2×) 155 AH

OPTIONAL BATTERY AH RATING:

UP TO (2×) 225 AH

BATTERY RUN TIME (STANDARD):

UP TO 3.5 HRS.

CHARGER (AUTOMATIC):

8 AMP

DRIVE SYSTEM

STANDARD DRIVE:

PAD ASSIST

0.75 hp (559 watts), ALL GEAR/
SEALED

FORWARD SPEED:

0-230 FT/MIN (4 mph) (6 kph)

REVERSE SPEED:

0-130 FT/MIN (2 mph) (3 kph)

PRODUCTIVITY

SCRUBBING WIDTH:

17'', 20'', 23''

17'', 20'', 23'', 24'', 26'', 28''

SCRUBBING RATE/HOUR :

22,124 FT/HR (6,743 m/hr)

25,543 FT/HR (7,786 m/hr)

Содержание 17'' DISK PAD ASSIST













































Результаты поиска

Содержание 17'' DISK PAD ASSIST

Отзывы:

Бренды по названию

Популярные бренды

MiniMag 17'' DISK PAD ASSIST, Руководство по эксплуатации

Результаты поиска

Содержание 17'' DISK PAD ASSIST

Отзывы:

Бренды по названию

Популярные бренды