MiniMag 17'' DISK PAD ASSIST Скачать руководство пользователя | Manualshive

Страница: 2 / 44

background image

- 2 -

M

INI

M

AG

-OP-EN

INTRODUCTION

This manual is furnished with each new machine. This manual will allow the Operator to get the best performance out of
your RPS manufactured Scrubber-Drier, Sweeper, Burnisher, or Orbital Scrubber. Read this manual thoroughly before
operating or servicing the machine.

This machine will provide excellent performance, but the best results will be obtained at the most minimum costs if:

• The machine is regularly maintained - per the machine Preventative Maintenance instructions provided.

• The machine is operated with reasonable care and caution.

• The machine is maintained with manufacturer supplied parts.

ABOUT THIS MANUAL

TABLE OF CONTENTS:

Tells you where to look in the manual.

SAFETY MESSAGES

: Section contains important information regarding hazard or unsafe practices of the machine. Lev-

els of hazards are identifi ed that could result in product or personal injury, or severe injury resulting in death.

OPERATION CONTROLS / MACHINE COMPONENTS

: Shows you the different machine controls and features.

MACHINE SETUP

: Tells you how to setup machine from un-crating to installing squeegee and brushes.

MACHINE OPERATION

: Section is to familiarize the operator with the operation and function of the machine.

BATTERY CHARGING

: Shows you how to charge the Batteries (on-board and off board charging).

MAINTENANCE

: This section contains preventative maintenance to keep the machine and it’s components in good work-

ing condition. They are listed in this general order:

• Batteries
• Scrub Brushes
• Adjusting Squeegee
• Service Schedule
• Machine Trouble Shooting

TROUBLE SHOOTING

: A list of common problems that may occur.

MACHINE SPECS:

Tells you Machine Specifi cations for the various parts of the machine.

MACHINE INSTALL FORM

: Should be fi lled out upon machine installation and faxed to 1-866-632-6961 or online at

www.rpscorporation.com.

WARRANTY POLICY

: Tells you coverage, exclusions and limitations to warranty.

NOTE

: The Serial Number of your machine is located on the lower half of the control panel of the machine.

AS OUR POLICY IS ONE OF CONSTANT IMPROVEMENT - ALL INFORMATION AND

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

SERIAL NUMBER

«
1
2
3
4
...
»

Содержание 17'' DISK PAD ASSIST













































Отзывы:

Нет отзывов

Похожие инструкции для 17'' DISK PAD ASSIST

PIXMA MX882 Series

Бренд: Canon Страницы: 80

MultiPASS C3500

Бренд: Canon Страницы: 47

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 212

Terra 3700B 908 4203 010

Бренд: Nilfisk-Advance Страницы: 68

Бренд: Janome Страницы: 42

E12327-00 BIG BERTHA XSM30

Бренд: BETCO Страницы: 36

STAC Vision 1.5

Бренд: Zeck Audio Страницы: 15

Бренд: Baby Lock Страницы: 200

Бренд: Ricoh Страницы: 134

Бренд: Olivetti Страницы: 76

Бренд: Stern Pinball Страницы: 44

Бренд: Square Scrub Страницы: 9

Pioneer Eclipse 225BU

Бренд: Amano Страницы: 26

Бренд: BH FITNESS Страницы: 30

Бренд: Riccar Страницы: 16

Бренд: Dustbane Страницы: 6

Integra LA 19934

Бренд: Dustbane Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды