Mini?Cam PCB-001-388 Скачать руководство пользователя страница 19

Страница: 19 / 20

PCB CHANGE HISTORY

PCB-001-388

REVISION A (09/2017)

Changes made between Versions 2A and 3A - 21/07/10 (PCB revision)

1. Remove Op-Amps & Filter. Replaced with dual gate driver

2. Remove switchable low frequency parallel tuned circuit

3. Replace 6 way JST ZR connector with individual cable termina ons

4. Replace Samtec PGP Pogos with Samtec SFM 1.27mm pitch socket

Changes made between Versions 3A and 4A - 27/07/10 (PCB revision)

1. Add test points for rod connec on

Changes made between Versions 4A and 4C- 08/02/11 (BOM revision)

1. Add Mini-Cam part numbers

Changes made between Versions 4C and 5A- 16/02/11 (PCB revision)

1. Swap connec ons to driver outputs & SSR switch connec ons to facilitate PCB rou ng

2. Move antenna connector on PCB to ease connec on

3. Remove antenna hole

4. R16 becomes 22R 1206 (was 10R). Sage PN remains the same, sage descrip on is changed.

5. Supply ﬁlter added (L1 & C14)

6. R3 becomes 220R 0402 (was 100R 0402)

Changes made between Versions 5A and 6A- 23/03/11 (PCB revision)

1. Change test point posi ons on PCB

PAGE 17

Содержание PCB-001-388





















Результаты поиска

Содержание PCB-001-388

Отзывы:

Похожие инструкции для PCB-001-388

Бренды по названию

Популярные бренды

Mini?Cam PCB-001-388, Техническая справочная документация

Результаты поиска

Содержание PCB-001-388

Отзывы:

Похожие инструкции для PCB-001-388

Бренды по названию

Популярные бренды