Mindray BeneVision N19 Скачать руководство пользователя страница 52

Страница: 52 / 105

4-2

BeneVision N22/BeneVision N19 Patient Monitor Service Manual

4.5

Technical Alarm Check

Before troubleshooting the patient monitor, check for technical alarm message. If an alarm message is presented,

eliminate the technical alarm first. For detailed information on technical alarm messages, possible causes and

countermeasures, refer to N series Operator’s Manual (P/N: 046-011259-00).

4.6

Blank Screen upon Startup

Remove AC and connect

after 5s, and press the

power-on button

The power LED of the module

rack is ON or the alarm LED of the

front housing is blinking?

Check the

power on

signal cable

of the front

housing

Remove AC, and press the

power on/off button for 15s

to restart the system if the

battery is available

Front housing

display

interface board

defective

AC LED is ON?

Power-on button

LED is ON?

Check ACDC, and

the ACDC may be

damaged.

Battery is provided?

The coaxial
cable of the

interface is

damaged

Arranged according to the possible order

Screen line,

screen and

backlight line

defective

Mother

control board

defective

The coaxial
cable of the

display

interface is

damaged

DCDC

board

failure

Содержание BeneVision N19










































































































Результаты поиска

Содержание BeneVision N19

Отзывы:

Похожие инструкции для BeneVision N19

Бренды по названию

Популярные бренды

Mindray BeneVision N19, Руководство по обслуживанию

Результаты поиска

Содержание BeneVision N19

Отзывы:

Похожие инструкции для BeneVision N19

Бренды по названию

Популярные бренды