Minarik XP-AC Series Скачать руководство пользователя страница 3

Страница: 3 / 32

Safety Warnings

Have a qualified electrical maintenance technician install, adjust, and service this

equipment. Follow the National Electrical Code and all other applicable electrical and

safety codes, including the provisions of the Occupational Safety and Healthy Act

(OSHA) when installing equipment.

Reduce the chance of an electrical fire, shock, or explosion by proper grounding, over

current protection, thermal protection, and enclosure. Follow sound maintenance

procedures.

It is possible for a drive to run at full speed as a result of a component failure. Install a

master switch in the AC line for stopping the drive in an emergency.

This drive is not isolated from earth ground. Circuit potentials are at 115 VAC above

earth ground. Avoid direct contact with the printed circuit board or with circuit elements

to prevent the risk of serious injury or fatality. Use a non-metallic screwdriver for adjust-

ing the calibration trimpots.

•

Содержание XP-AC Series

































Результаты поиска

Содержание XP-AC Series

Отзывы:

Похожие инструкции для XP-AC Series

Бренды по названию

Популярные бренды

Minarik XP-AC Series, Руководство пользователя

Результаты поиска

Содержание XP-AC Series

Отзывы:

Похожие инструкции для XP-AC Series

Бренды по названию

Популярные бренды