Minarik XP-AC Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

background image

Installation

It may be necessary to earth ground the shielded cable. If noise is produced by devices

other than the drive, ground the shield at the drive end. If noise is generated by a

device on the drive, ground the shield at the end away from the drive. Do not ground

both ends of the shield.

Keep logic wires away from the power carrying lines or sources of electrical noise that

can cause erratic operation.

Heat sinking

Model XP10-115AC requires an additional heat sink when the continuous armature cur-

rent is above 5 ADC. Use Minarik

®

part number 223-0159. All other chassis drives have

sufficient heat sinking in their basic configurations. Use a thermally conductive heat sink

compound (such as Dow Corning

®

340 Heat Sink Compound) between the drive chassis

and heat sink surface for optimum heat transfer.

Line fusing

Protect all Minarik drives with AC line fuses. Use fast acting AC line fuses rated for 250

volts, and approximately 150% – 200% of the maximum armature current. Fuse only the

“hot” side of the AC line (L1) if using 115 VAC line voltage. See the chart below for recom-

mended line fuse sizes.

•

•

Maximum Armature

Current (DC Amps)

1.5 & below

2.6

3.5

5.0

7.6

10

AC Line Fuse

Rating (AC Amps)

3

5

8

10

15

15

Recommended Line Fuse Sizes

«
...
8
9
10
11
12
...
»

Содержание XP-AC Series

































Отзывы:

Нет отзывов

Похожие инструкции для XP-AC Series

Бренд: Bardac Страницы: 62

Бренд: RHINO MOTION CONTROLS Страницы: 10

Бренд: FMX Страницы: 256

Бренд: Eskridge Страницы: 7

Бренд: Cole Parmer Страницы: 8

Бренд: Leadshine Страницы: 13

Бренд: Minolta Страницы: 26

Servo Motor Kit

Бренд: Terasic Страницы: 20

AC Tech PositionServo 940

Бренд: Lenze Страницы: 75

Бренд: Technosoft Страницы: 88

Бренд: Vacon Страницы: 28

Бренд: Oerlikon Страницы: 56

W-DRIVEB2M2M/08

Бренд: HIDROCONTROL Страницы: 28

VLT HVAC Drive FC 131

Бренд: Danfoss Страницы: 54

Бренд: Samsung Страницы: 32

Sinamics SM150 6SL3845-2NN41-8AD0

Бренд: Siemens Страницы: 192

Бренд: HP Страницы: 4

ACS580-01 Series

Бренд: ABB Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды