manualshive.com logo in svg

Minarik MM21051C, Руководство пользователя

Поделиться
Скачать
Minarik MM21051C Скачать руководство пользователя страница 46

40

Before applying power

Perform the following steps before starting any procedure in this
section:
1.  Disconnect AC line voltage from the drive.
2.  Check the drive closely for damaged components.
3.  Check that no conductive or other foreign material has become

lodged on the printed circuit board.

4.  Verify that every connection is correct and in good 

condition.

5.  Verify that there are no short circuits or grounded connections.
6.  Check that the voltage selection switch settings match the AC

line and output voltages.

7.  Check that the drive’s rated armature and field outputs are

consistent with the motor ratings.

For additional assistance, contact your local Minarik distributor, or
the factory direct:   (800) MINARIK (phone) or (800)646-2745

(800) 394-6334 (fax)

Warning

Dangerous voltages exist on the drive when it is powered.
When possible, disconnect the drive while troubleshooting.
High voltages can cause serious or fatal injury.

Troubleshooting

Содержание MM21051C

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды