Milwaukee MW180 MAX Скачать руководство пользователя страница 60

Страница: 60 / 64

MW180 pH / mV / EC / TDS / NaCl / Temperature Bench Meter

14. TROUBLESHOOTING

SYMPTOMS

PROBLEM

SOLUTION

Slow response /

Excessive drift

Dirty pH electrode

pH electrode: Soak the electrode tip in

MA9016

for 30 minutes, then follow the

Cleaning procedure

Dirty conductivity probe

EC probe: Remove and clean the sleeve.

Make sure the four rings on the probe

are clean.

Reading fluctuates

up and down

(noise)

Clogged/dirty pH electrode

junction. Low electrolyte level

(refillable electrodes only)

Clean the electrode. Refill with fresh

MA9012

electrolyte

Conductivity probe sleeve not

properly inserted; air bubbles

inside sleeve.

Make sure the sleeve is correctly placed.

Tap the probe to remove air bubbles.

Display shows the

reading blinking.

Reading out of range

Recalibrate the meter.

Check the sample is within measurable

range.

Make sure the autoranging feature is not

enabled.

Meter fails to

calibrate or gives

faulty readings

Broken probe

Replace the probe.

LCD tags displayed

continuously at

startup

ON/OFF key

is blocked

Check the keyboard.

If error persists, contact Milwaukee

Technical Service.

“Internal Er X”

Internal hardware error

Restart the meter.

If error persists, contact Milwaukee

Technical Service.

Содержание MW180 MAX

































































Результаты поиска

Содержание MW180 MAX

Отзывы:

Похожие инструкции для MW180 MAX

Бренды по названию

Популярные бренды

Milwaukee MW180 MAX, Инструкция по эксплуатации

Результаты поиска

Содержание MW180 MAX

Отзывы:

Похожие инструкции для MW180 MAX

Бренды по названию

Популярные бренды