Milwaukee MAX MW160 Скачать руководство пользователя страница 41

Страница: 41 / 44

CERTIFICATION

Milwaukee Instruments conform to the CE European Directives.

Disposal of Electrical & Electronic Equipment.

Do not treat this product as household

waste. Hand it over to the appropriate collection point for the recycling of electrical and

electronic equipment.
Please note: proper product disposal prevents potential negative consequences

for human health and the environment. For detailed information, contact your local

household waste disposal service or go to

www.milwaukeeinstruments.com

(US only)

www.milwaukeeinst.com

RECOMMENDATION

Before using this product, make sure it is entirely suitable for your specific application

and for the environment in which it is used. Any modification introduced by the user

to the supplied equipment may compromise the meter’s performance. For your and the

meter’s safety do not use or store the meter in hazardous environment. To avoid damage

or burn, do not perform any measurement in microwave ovens.

Содержание MAX MW160













































Результаты поиска

Содержание MAX MW160

Отзывы:

Похожие инструкции для MAX MW160

Бренды по названию

Популярные бренды

Milwaukee MAX MW160, Инструкция по эксплуатации

Результаты поиска

Содержание MAX MW160

Отзывы:

Похожие инструкции для MAX MW160

Бренды по названию

Популярные бренды