Milwaukee MAX MW160 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

background image

22

MW160

Bench Meter

8.3. MEASUREMENT

Make sure the instrument has been calibrated before taking pH measurements.

1. Remove the probe protective cap and place the tip approximately 4 cm (1 ½”) into the

sample. It is recommended to wait for the sample and the pH probe to reach the same

temperature.

2. If necessary, press RANGE until the display changes to pH measurement range. Allow

the reading to stabilize (blinking WAIT tag disappears).

The LCD will display:

y

measurement and temperature readings

y

temperature compensation mode (MTC or ATC)

y

buffers used (if option enabled in Setup)

For best results is recommended to:

y

Calibrate the probe before use and recalibrate periodically.

y

Keep the electrode hydrated.

y

Rinse the probe with the sample before use.

y

Soak in

MA9015

Storage solution for at least 1 hour before measurement.

MTC mode

If Manual Temperature Compensation (MTC) is desired, the temperature probe must be

disconnected from the instrument.
The LCD displays the default temperature of 25 °C or the last temperature reading with the

blinking MTC and °C (or °F) tags.

The temperature can be adjusted using the

keys (from –20.0 °C to 120.0 °C).

«
...
20
21
22
23
24
...
»

Содержание MAX MW160













































Отзывы:

Нет отзывов

Похожие инструкции для MAX MW160

Бренд: ABB Страницы: 8

Бренд: Igema Страницы: 30

Бренд: z-laser Страницы: 62

Бренд: i-SENS Страницы: 50

Бренд: Waterproof Страницы: 10

Бренд: Ocean Optics Страницы: 43

Бренд: Ocean Technology Systems Страницы: 12

Бренд: Ocean Reef Страницы: 24

Бренд: Teledyne Hastings Instruments Страницы: 54

Бренд: Endress+Hauser Страницы: 88

Бренд: AccuMac Страницы: 10

STORA-ABG RKS-01

Бренд: ECOTEST Страницы: 146

Бренд: Bühler technologies Страницы: 33

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Precision KMS7101

Бренд: Kreg Страницы: 16

Бренд: Eurotron Страницы: 122

Бренд: Hanna Instruments Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды