Miller PipeWorx 400 Скачать руководство пользователя страница 86

Страница: 86 / 120

OM-236 891 Page 82

H43

Motor Right

Indicates motor error on right motor. Check right feeder drive

housing and wire spool for obstructions. If this code continues

to appear on the display, contact the nearest Factory Author-

ized Service Agent.

H44

Motor Low Bus

Indicates input primary line voltage is too low or power source

is incorrectly linked.

Increase primary line voltage to at least 90% of specified

nominal voltage.

Check for correct voltage linking (see Section 5-9).

If this code continues to appear on the display, contact the

nearest Factory Authorized Service Agent.

H45

Button Stuck Feeder

Indicates button is stuck on the feeder upon feeder power up.

Fault will clear when button is released.

H46

Trigger Stuck Left

Indicates left trigger stuck fault. Fault will clear when left trigger

is released.

H47

Trigger Stuck Right

Indicates right trigger stuck fault. Fault will clear when right

trigger is released.

H48

Trigger Fault Left

Indicates left trigger was held too long in trigger jog (the lesser

of 60 seconds or 30 ft (9.1 m) of wire.

H49

Trigger Fault Right

Indicates right trigger was held too long in trigger jog (the lesser

of 60 seconds or 30 ft (9.1 m) of wire.

H60

Memory Card Fault

Indicates unable to read memory card. Faulty memory card or

wrong format.

H61

File Read Error

Indicates faulty file on memory card.

H62

File Write Error

Indicates full or faulty memory card.

H63

Invalid File

Indicates an invalid file on memory card. The system was able

to read the file; however, the contents of the file were invalid.

Remove card or press any button to clear error.

H64

Memory Card Locked

Indicates a save was attempted to a locked card. This refers to

the physical switch on the memory card. Unlock the memory

card and try again. Try a different memory card. Remove card

or press any button to clear error. If this code continues to ap-

pear on the display, contact the nearest Factory Authorized

Service Agent.

H65

Read Only File

Indicates a save was attempted to a file that has been marked

read-only. Check with the appropriate person to see if the attrib-

utes are read only for a reason (the attributes can be altered

using a PC). Use a different card. Remove card or press any

button to clear error.

H66

No Memory Card Detected

Indicates no memory card detected when a memory card oper-

ation was attempted. Insert a card or press any button to clear

error. Try a different memory card. If this code continues to

appear on the display, contact the nearest Factory Authorized

Service Agent.

H70

Weld Library

Indicates missing/incomplete weld library in power source.

Weld library must be loaded from memory card.

H98

Serial Communication Loss

Indicates serial communication was initially made and is now

malfunctioning. Check wire feeder/power source control cable

connection and tighten if necessary. May appear normally dur-

ing firmware updates. If this code continues to appear on the

display, contact the nearest Factory Authorized Service Agent.

H99

Serial Communication Malfunction

Indicates serial communication is malfunctioning. If error ap-

pears on power source and wire feeder, unit might be linked for

460 VAC and 208-230 input power is being applied. Check

primary power and link unit accordingly. Check wire

feeder/power source control cable connection and tighten if

necessary. May appear normally during firmware updates. If

this code continues to appear on the display, contact the

nearest Factory Authorized Service Agent.

Содержание PipeWorx 400

























































































































Результаты поиска

Содержание PipeWorx 400

Отзывы:

Похожие инструкции для PipeWorx 400

Бренды по названию

Популярные бренды

Miller PipeWorx 400, Руководство пользователя

Результаты поиска

Содержание PipeWorx 400

Отзывы:

Похожие инструкции для PipeWorx 400

Бренды по названию

Популярные бренды