Miller Electric Millermatic 250, Руководство пользователя

Страница: 28 / 32

OM–1308 Page 24
Table 6-1. Drive Roll And Wire Guide Kits
Note
Base selection of drive rolls upon the following recommended usages:
1 V-Grooved rolls for hard wire.
2 U-Grooved rolls for soft and soft shelled cored wires.
3 U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).
4 V-Knurled rolls for hard shelled cored wires.
5 Drive roll types may be mixed to suit particular requirements (example: V-Knurled roll in combination
with U-Grooved).
Ref. S-0026-B/7-91
Wire Diameter
Fraction Decimal Metric
.023/.025 in.
.030 in.
.035 in.
.045 in.
.023/.025 in.
.030 in.
.035 in.
.045 in.
0.6 mm
0.8 mm
0.9 mm
1.2 mm
Kit No.
087 131
079 594
079 595
079 596
Drive Roll
Part No. Type
087 130
053 695
053 700
053 697
V-Grooved
V-Grooved
V-Grooved
V-Grooved
Inlet
056 192
056 192
056 192
056 193
Wire Guide
Description
Part
No.
Dia.
Mkgs.
Item
No.
Figure 6-5. Panel, Rear w/Components (Fig 6-1 Item 10)
Quantity
1 134 834 HOSE, SAE .187 ID x .410 OD (order by ft) 3ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 149 332 CLAMP, hose .405-.485clp dia slfttng 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 GS1 125 785 VALVE, 24VAC 2 way custom port 1/8 orf 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 143 810 PANEL, rear 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 169 654 BRACKET, support tank 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 602 387 CHAIN, weldless 2/0 x 27.000 lg 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 605 227 NUT, nyl hex jam .750NPST 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 044 426 CONNECTOR, clamp cable .690/1.070 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 010 493 BUSHING, snap-in nyl .625 ID x .875mtg hole 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 148 242 WINDTUNNEL, 9 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 FM1 148 808 MOTOR, fan 230V 1550RPM .312dia shaft 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 148 809 BLADE, fan 9 in 5wg 34deg .309 bore CCW 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 049 399 NUT, speed push-on-type .312 stud .625 OD x .456 ID 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
3
4
5
6
7
8
10
11
12
13
9
ST-148 327-C
.
Hardware is common and
not available unless listed.
Figure 6-5. Panel, Rear w/Components
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.