Miller Electric Big 40 WG Скачать руководство пользователя страница 43

Страница: 43 / 80

OM-4405 Page 39

8-7.

Adjusting Governor Sensitivity

802 780 / Ref. 115 155-A

Governor sensitivity may re-
quire readjustment if weld
speed is adjusted. Weld speed
must be readjusted if sensitivity
is adjusted.

Be sure carburetor and link-
ages are adjusted properly be-
fore adjusting sensitivity.

Start engine. Apply and remove
load.

Locking Nuts

Sensitivity Adjustment Screw

Governor Spring

If engine is slow to pick up load or
rpm drops under load, adjust spring
tension as follows:

Loosen top nut and tighten bottom
nut to move screw down. Tighten
nuts.

If engine hunts with or without load,
adjust spring tension as follows:

Loosen bottom nut and tighten top
nut to move screw up. Tighten nuts.

Stop engine.

Close door.

Tools Needed:

1/2 in

Notes

Содержание Big 40 WG

















































































Результаты поиска

Содержание Big 40 WG

Отзывы:

Похожие инструкции для Big 40 WG

Бренды по названию

Популярные бренды

Miller Electric Big 40 WG, Руководство пользователя

Результаты поиска

Содержание Big 40 WG

Отзывы:

Похожие инструкции для Big 40 WG

Бренды по названию

Популярные бренды