Miller Electric Big 40 WG Скачать руководство пользователя страница 36

Страница: 36 / 80

OM-4405 Page 32

7-3.

Optional Auxiliary Power Receptacles

120 V 20 A AC GFCI
Receptacle GFCI1

240 V 16 A AC European
Receptacle RC1

240 V 15 A AC Australian
Receptacle RC1

240 V 15 A AC South African
Receptacle RC1

Receptacles supply 60 Hz single-
phase power at weld/power speed.

If a ground fault is detected, the
GFCI Reset button pops out and
the receptacle does not work.
Check for faulty tools plugged in
receptacle. Press button to reset
GFCI1.

At least once a month, run en-
gine at weld/power speed and
press test button to verify GFCI
is working properly.

Circuit Breaker CB2

Circuit Breaker CB3

CB2 protects GFCI1 from overload.
If CB2 opens, GFCI1 does not
work. Place button to reset breaker.

CB3 protects RC1 from overload. If
CB3 opens, RC1 does not work.
Press button to reset breaker.

If a circuit breaker continues to
open, contact Factory Autho-
rized Service Agent.

Auxiliary power is not affected
by weld output.

Maximum output is 2.4 kVA/kW
from GFCI1 and 4 kVA/kW from
RC1. Maximum output from all re-
ceptacles is 4 kVA/kW.

EXAMPLE: If 13 A is drawn from
RC1, only 7 A is available at GFCI1:

(240 V x 13 A) + (120 V x 7 A) =
4.0 kVA/kW

191 624

European Receptacle

Australian Receptacle

South African Receptacle

Содержание Big 40 WG

















































































Результаты поиска

Содержание Big 40 WG

Отзывы:

Похожие инструкции для Big 40 WG

Бренды по названию

Популярные бренды

Miller Electric Big 40 WG, Руководство пользователя

Результаты поиска

Содержание Big 40 WG

Отзывы:

Похожие инструкции для Big 40 WG

Бренды по названию

Популярные бренды