Milestone pro MP-SC-5TDS Скачать руководство пользователя страница 8

Страница: 8 / 48

Compact Scaler Switcher (with PoH)

2. Panel Description

2.1 Front Panel

①

Built-in IR Receiver

②

Power indicator



Off when there is no power to the device



Green when the device is in standby mode



Red when the device is powered on.

③

1-HDMI/MHL input Selector & Activity LED

④

2-HDMI input Selector & Activity LED

⑤

3-HDMI input Selector & Activity LED

⑥

4-DisplayPort input Selector & Activity LED

⑦

5-VGA input Selector Activity LED

⑧

Auto-Switching Mode Selector& Activity LED



Press this button to enter or exit Auto-switching mode, in this mode, select
input source via front panel button is not available, but RS232 command and IR
remote are able to switch mode. The auto LED turn green and keep on.

Note:

When you set any VGA port to C-video or YPbPr in Manual-switching mode,

the system will not be able to enter Auto-switching mode.

⑨

Volume Knob

Note:

Pictures shown in this manual are for reference only, different model and

specifications are subject to real product.

MP-SC-5TDS

SOURCE

MIC

VOLUME

1-HDMI/MHL

5-VGA

4-DP

3-HDMI

2-HDMI

AUTO

Содержание MP-SC-5TDS
















































Результаты поиска

Содержание MP-SC-5TDS

Отзывы:

Похожие инструкции для MP-SC-5TDS

Бренды по названию

Популярные бренды

Milestone pro MP-SC-5TDS, Руководство пользователя

Результаты поиска

Содержание MP-SC-5TDS

Отзывы:

Похожие инструкции для MP-SC-5TDS

Бренды по названию

Популярные бренды