Regulatory Approvals
FCC Class A
UL 1950
CSA 22 No. 950
EN60950
CE
– EN55022 Class B
– EN50082-1
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the
Low Voltage Directive (73/23/EEC) issued by the commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
EN55022 (CISPR 22) - Radio Frequency Interference
EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
EN60950 (IEC950) - Product Safety
To Contact Technical Support:
For prompt response when calling for technical support, have the following information
ready: product serial number, date of purchase, vendor or place of purchase.
Contact one of the following:
In North America: call +1.408.744.2751 or email: [email protected]
International: call +49.231.97.47.780 or email: [email protected]
© 2000 MiLAN, the MiLAN logo, and MiLAN Technology are either trademarks or registered trademarks of Digi International,
Inc. in the United States and/or other countries. All other trademarks are the property of their respective holders.
Installation
Turn off any connected devices before beginning
installation. To install the MIL-05T:
1. Attach the T-type connector from your network
cabling to the BNC connector on the MIL-05T.
2. Connect the 15-pin AUI connector on the MIL-05T
to the 15-pin AUI on the computer.
3. Secure the connection with the slide-lock mechanism
by engaging lock pins on the MIL-05T
4. Reboot the computer. The PWR LED and the SQE LED (if enabled)
both illuminates.
Troubleshooting
If the PWR LED does not illuminate:
1. Turn off the computer.
2. Check all connections- Start with the MIL-05T unit itself. Then check
the network connections.
3. Restart the computer.
4. If power LED still does not illuminate, call MiLAN's technical support.
Disabling or Enabling SQE
The SQE slide switch is located on the lower, right-hand
side of the unit. To enable or disable the SQE jumper:
• Disable (default): Slide the switch right to the Off position.
• Enable: Slide the switch left to the On position.
Dimensions
Dimensions for the MIL-05T: 2.2" H x 1.63" W x .63" D
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of its products,
and all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the
performance of the product delivered hereunder. MiLAN Technology will in no case cover
damages arising out of the product being used in a negligent fashion or manner.
MIL-05T
Micro-Twist
10BASE-T
Ethernet Transceiver
MODEL: MIL-05T
Installation Guide
90000122 REV. C Printed in the USA
2
3
15-Pin Connector
OFF
SQE
Slide
Switch
ON
Figure 1. Inside the MIL-05T
microMmau
m”†‡‘@mil
-
PUt
ethernet@thin@coax
@
QPbƒ˜‡R
transceiver
p”œ‡—@r‡–š‹—‡†Z@QR@vdc@RPP@’a
fcc@part@QU@class@a
compliant
SQE
O
N
S
Q
E
O
F
F
PWR
