7
Migatronic Focus ADF Welding and Grinding Helmet (ENGLISH)
MAINTENANCE
REPLACEMENT OF EXTERNAL
SHIELDING GLASS
•
Remove the 2 thumb screws, frame and filter,
then remove the external shielding glass from
the recess on the inside of the helmet.
•
Make sure the protective films are removed from
new external shielding glasses.
• Place the new external shielding glass in the
recess on the inside of the helmet, then replace
the frame, filter and thumb screws.
• Only use original Migatronic shielding glasses.
Use of lower-grade glasses may cause warping
and allow spatter to damage the filter, so
invalidating the warranty. This may also reduce
the impact rating.
NOTE –
Do not use the helmet without the
shielding glass in place
REPLACEMENT OF INTERNAL
SHIELDING GLASS
• Remove the internal shielding glass by pulling
out the top edge at the notch at the back of
the filter.
•
Mount the new internal shielding glass after you
have removed the protective film.
•
Insert the glass under the frame at one side,
bend the glass in the middle and place it under
the frame at the other side.
REPLACEMENT OF WELDING FILTER
•
Prise off the shade adjusting knob from
the outside of the helmet and unscrew the
locking nut.
•
Prise off the Weld / Grind knob then release the
control module.
•
Remove the 2 thumb screws and top frame.
•
Remove the filter and mount the new filter.
INSPECTION
•
Carefully inspect your Migatronic Auto Darkening
Welding Filter regularly.
•
Cracked or scratched filter glasses or shielding
glasses reduce the field of view and seriously
impair protection. They should be replaced
immediately to avoid damage to the eyes.
•
Inspect the complete helmet frequently and
replace any worn or damaged parts
CLEANING
• Clean the helmet with mild soap and a damp
cloth.
•
Clean the welding filter with clean lint-free tissue
or cloth.
• Do not immerse in water.
• Do not use solvents.
4
10 15 20 30
0
0
2
5
7
1
0
5
1
5
2
1
5
5
.
2
1
5
.
0
0
0
5
0
5
4
0
0
1
0
8
0
6
0
4
225 250 275 300
CURRENT AMPERES
4
1
1
1
e
d
a
h
S
0
1
9
e
d
a
h
S
Shade 13
Shade 12
350 400
Shade 11
5
1
e
d
a
h
S
0
1
e
d
a
h
S
11
12
13
14
14
Shade 10
Shade 11
Shade 12
Shade 13
Shade 14
15
Shade 13
Shade 12
Shade 10
Shade 14 Shade 15
Shade 9
10
Shade 11
Shade 12
8
9
10
11
Shade 13
Shade 14
Shade 10
11
12
Shade 13
5
1
e
d
a
h
S
2
1
e
d
a
h
S
Shade 13
Shade 14
Shade 11
Shade 12
Shade 13
5
6
7
WELDING PROCESS
Covered Electrodes
MIG Plate Welding
MIG Sheet Welding
TIG
MAG
Arc Gouging
Plasma Cutting
Plasma Welding
RECOMMENDED SHADE NUMBERS
Migatronic Focus ADF Welding and Grinding Helmet (ENGLISH)
EC DECLARATION OF CONFORMITY
MIGATRONIC A/S, Aggersundvej 33, 9690 Fjerritslev, Denmark
declares that the product stated below
Type: Welding Helmet Focus ADF
conforms to the provisions of (EU) 2016/425 for Personal
Protective Equipment (PPE)
European Standards: EN175, EN379, EN166
Notified Body: ECS GmbH - European Certification Service
Obere Bahnstraße 74, 73431 Aalen
Notified Body number: 1883
Issued in Fjerritslev 12.11.2020
Kristian M. Madsen
CEO
FAULT FINDING
IRREGULAR DARKENING
• Headband has been set unevenly so the
distance between the eyes and the lens is
different from the left to the right.
AUTO DARKENING FILTER DOES NOT
DARKEN OR FLICKERS
• External shielding glass is soiled, clean or
replace it.
•
Photo sensors are dirty, wipe clean with a soft
lint-free cloth.
• Welding current is too low, select the slow
position on the filter and ensure the view of the
weld is unobstructed.
• Change to high sensitivity.
POOR VISION
•
Ensure the shielding glass and the filter cartridge
are clean.
• Ensure the shade number is correct and adjust
accordingly.
• Ensure ambient light is not too low.
WARRANTY
Migatronic warrants to the purchaser that the
product will be free from defects in material and
workmanship for the period of 12 months from the
date of sale to the buyer.
The manufacturer’s sole obligation under this
warranty is limited to making replacement or
repairs, or to refund the purchase price of the
product with defects.
This warranty does not cover product malfunctions
or damage resulting from the product being
tampered with or misused.
The operating instructions must be followed;
failure to observe the instructions will invalidate
the warranty.
The manufacturer is not responsible for any
indirect damage arising out of the use of the
product.
MARKINGS
The filter is marked with the shade range and
optical classification.
The following in an example of EN379:
The shielding glasses are marked with the optical
class and impact rating.
The following is an example of EN166
Light Shade
Dark Shade DIN 5-8
Dark Shade DIN 9-13
Manufacturer Identification
Optical Class
Diffusion of Light Class
Variations in Luminors Transmittance Class
Angle Dependency Class
Certification Mark or Number Standard
4/5 - 8/9 - 13 MG 1/1/1/2 EN379 CE
Manufacturer Identification
Optical Class
Impact Rating
MG 1 B CE
Содержание FOCUS ADF
Страница 2: ...2...
