background image

8

Wireless Drive-Alert Control Panel Terminals and Hooking Up Other Equipment

The terminal block, TB1, provides a convenient wire connection point for external device control and test points.  

NOTE:  All external devices must be rated at 24 VDC

The DA-600/DA-605 terminals on the bottom left of the Control Panel’s green PCB, with the “Alert” and “Power” LEDs to the right 

•  Valid XMSN-  

Valid Transmission LED (far left) is RED and indicates if a valid signal is received from the Sensor/Transmitter

•  LOW BATT - 

Low Battery LED is YELLOW and indicates if the batteries in the Sensor/Transmitter are running low

•  SIG -  

 

Received Signal Strength (e.g. 1-1.5VDC = No Signal; 1.6-2.5VDC = Signal

•  +5VDC -    

5 Volt DC Logic Power @ 25mA (max)

•  ALA -  

 

Alarm Signal (0-1vdc = No Alarm; 4-5 VDC = Alarm)

•  GND -  

 

Unit Ground

•  +24VDC -    

Power Supply for 24VDC @ 100 mA (.1 amp) maximum accessories

•  NO -  

 

Normally Open Relay Contact

•  NC -  

 

Normally Closed Relay Contact

•  C -   

 

Common Relay Contact

•  NO -  

 

Normally Open Relay Contact

•  C -   

 

Common Relay Contact

ALERT LED -    

Alert LED is RED and lights when the Sensor/Transmitter has detected an intrusion and is sending a signal

POWER LED -    

Power LED is GREEN and remains on when the Control Panel/Receiver is plugged in and receiving power

NOTE:  The Control Panel/Receiver will operate on 12 VDC.  An auto battery with the positive (+) connected to the +24 VDC 
terminal and negative (-) connected to the GND terminal will operate the Drive-Alert.  Therefore, the Control Panel/Receiver can 
become portable (the sensor is always portable) so the unit can be used in a vehicle or at a remote site.

***** NOTE:  DO NOT PLUG THE UNIT INTO 110 VAC IF ALSO OPERATED ON BATTERY AS IT CAUSES FAILURE *****

   SIG    ALA  +5VDC  GND 

+24DC

    NO      NC        C        NO       C

Connecting Line of Sight Wireless Transmitter

such as Mier’s DA-606LK Light Kit

The Black and Red Wires attach to the last two 
terminals (NO and C isolated contacts)

   SIG    ALA  +5VDC  GND 

+24DC

    NO      NC        C        NO       C

Maximum Current 
Limited to 1 Ampere

Connection using dry contacts and external power

* Maximum Voltage is 24V   
   DO NOT apply 120VAC

BELL

External Power

   SIG    ALA  +5VDC  GND 

+24DC

    NO      NC        C        NO       C

Connecting a DA-066MP Wireless Chime Transmitter to a

DA-600 Control Panel

DA-066MP Push-Button 
Wireless Chime Transmitter

Jumper

Black

White

Red

   SIG    ALA  +5VDC  GND 

+24DC

    NO      NC        C        NO       C

External 24VDC Bell with 
Whistle Switch ON or OFF

Capacitor
0.1 Microfarads 100 Volt (min)
Adding a capacitor extends the life 
of the relay.

NOTE:
Limit of two external bells

BELL

Connection using relay contacts switching internal power

Jumper

   SIG    ALA  +5VDC  GND 

+24DC

    NO      NC        C        NO       C

NOTE:  If using a 

DA-500 hard-wired system

, and the internal piezo whistle is not wanted, move the 

Whistle Switch to the OFF position and connect the jumper b24 and the C Terminal

1N4004 DIODE
Adding the diode extends the life of the relay.

RELAY

External Relay 

Hookup

24VDC

To AC operated CHIMES/ALARMS

Connection using relay contacts switching internal power

Jumper

Black  Red

Содержание DA-600














Отзывы: