11
Supplemental Specifications
DA-600 and DA-605 CONTROL PANEL/RECEIVER:
1.
INPUT POWER: 120 VOLTS AC 50/60 HZ, 3 WATTS
2.
OUTPUT POWER: 24 VOLTS DC AT 100 MILLIAMPERES (.1 AMP)
3.
FREQUENCY:
433.92 MHZ FIXED SUPERHETRODYNE
4.
ANTENNA:
¼ WAVE MONOPOLE FIXED BOLTED IN STEEL CASE 0 DBI GAIN
5.
RECEIVER:
LINX TECHNOLOGIES MODEL KH3
6.
ADDRESS CODES: FOUR POSITION DIP SWITCH
7.
LAMPS/LEDS:
POWER, LOW BATTERY, VALID XMSN, ALARM
8.
OUTPUT:
PIEZO WHISTLE AND 24 VOLT RELAY
9.
ALARM TIME:
ADJUSTABLE 2 TO 12 SECONDS FOR EACH ALARM.
10.
OPERATING TEMP: 0 DEGREE F. TO +105 DEGREE F.
11.
WEIGHT:
2.5 POUNDS.
DA-066MP WIRELESS CHIME TRANSMITTER:
The DA-066MP Remote Chime Transmitter is attached to a DA-605 Control Panel and is an option on the DA-600 or DA-500. It is a 315 Mhz transmitter with ASK/
OOK encoded signal. It is activated by a relay closure on a Drive-Alert, or by pushing the button on the case. It requires 15-30 volts DC on the RED and BLACK
wires. The WHITE wire when pulled to ground will activate the transmitter.
Frequency:
315 Mhz Crystal Controlled
Power:
.002 WATTS
Power Input:
15-30 Volts DC at .025 AMPS
Weight:
9 Ounces
Antenna:
1/8 Wave Quasi-Loop, -2 DBI Gain
Duty Cycle:
50% Encoder Duty Cycle at 1 Mhz
On Time:
Normally 1 Second of Transmit Time
FCC ID: SGXMPIDA066
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes not expressly authorized by Mier Products, Inc. may void the user’s authority to operate this equipment.
IC ID: 5583ADA-066MP
Cet appareil est conforme a des reglements d’industrie Canada exempts de license standard RSS (s). Son fonctionnement est soumis aux deux conditions:
(1) Ce dispositif ne doit pas causer d’interferences nuisibles
(2) Cel appareil doit accepter toute interference recue, y compris les interferences pouvant entrainer un functionnement indesirable.
DA-610TO SENSOR/TRANSMITTER:
1.
POWER REQUIREMENTS:
TWO (2) SIZE AA LITHIUM BATTERIES 3.0 VOLTS DC
2.
OPERATING FREQUENCY:
433.92 MHZ FIXED
3.
ANTENNA:
6.5 in wire internal to 6 ox
4.
TRANSMITTER OUTPUT:
2 MILLIWATTS
5.
TRANSMITTER:
LINX TECHNOLOGIES MODEL KH ENCODER/TRANSMITTER
6.
ENCODER MODULATION: AMPLITUDE ON-OFF KEYING (OOK) AT 1200 BPS.
7.
ADDRESS CODES:
JUMPER PLUGS ELECTED FOR THE ENCODER
8.
DATA:
ONE DATA BIT ENCODED WHEN BATTERY IS LOW.
9.
TRANSMITTER ON TIME:
LESS THAN 5 SECONDS FOR ANY SINGLE ALARM
10.
ENCLOSURE:
NON-METALLIC, WEATHER SEALED ENCLOSURE HOUSES THE TRANSMITTER
11.
QUIESCENT CURRENT :
60 MICROAMP
12.
ACTIVE CURRENT:
3 MILLIAMP
13.
BATTERY LIFE:
ABOUT 3 TO 5 YEARS IN RESIDENTIAL USE.
14.
OPERATING TEMP:
-40 DEGREES F TO + 125 DEGREES F
15.
WEIGHT:
THREE POUNDS
16.
DETECTION OF VEHICLES:
DISTANCE FROM SENSOR/TRANSMITTER UNIT FOR STANDARD SEDAN MOVING
AT 5 MPH+ IS 14 FEET (MAX), 9 FEET (MID), 7 FEET (MIN)
DA-611TO SENSOR/TRANSMITTER:
ALL SPECIFICATIONS ARE THE SAME AS THOSE LISTED FOR THE DA-610TO ABOVE, EXCEPT THE FOLLOWING:
A.
THE SENSOR IS NOT INSIDE THE ENCLOSURE WITH THE TRANSMITTER. IT IS AN EXTERNAL SENSOR
ATTACHED TO THE TRANSMITTER ENCLOSURE WITH 50’ OF CABLE (SEE OPTIONS PAGE)
B.
DETECTION OF VEHICLES: DISTANCE FROM SENSOR/ FOR STANDARD SEDAN MOVING AT 5 MPH+ IS 17 FEET (MAX), 12 FEET (MID), 10 FEET (MIN)
800-473-0213 ~ [email protected] ~ www.mierproducts.com
