Miele TKG 450 WP Скачать руководство пользователя страница 76

Страница: 76 / 80

Settings menu

Buzzer volume

The buzzer can be set to be louder or

quieter.

The setting selected is shown in a bar

chart.

Factory default: a medium setting.

– Quieter

      

– Louder

      

You will hear the buzzer change as the

setting is selected.

Keypad tone

When this function is activated, a tone

will sound each time a button is

pressed.

Options

– On
– Off (the machine is delivered with this

option selected as standard)

Conductivity



Low

This setting should only be

altered if the water is so soft that it is

likely to cause the electronics which

sense residual moisture in the

laundry to give false readings.

Options

– Normal (Factory default setting)
– Low

Condition for low conductivity setting

This programmable function should

only be set if the water used for

washing the laundry is extremely soft

with a conductivity reading (electrical

conductivity) less than 150 μS/cm.

Contact your local water authority for

the conductivity level of your mains

water supply.



Only activate the

Low

option if

the above condition is present.

Otherwise drying results will be

unsatisfactory.

Total consumption

You can display the total

consumption.

Options

– Display

The total consumption is displayed in

kWh.

– Reset function

The total consumption to date will be

deleted with the

Reset

option.

Содержание TKG 450 WP

















































































Результаты поиска

Содержание TKG 450 WP

Отзывы:

Похожие инструкции для TKG 450 WP

Бренды по названию

Популярные бренды

Miele TKG 450 WP, Руководство по эксплуатации

Результаты поиска

Содержание TKG 450 WP

Отзывы:

Похожие инструкции для TKG 450 WP

Бренды по названию

Популярные бренды