Miele TKG 450 WP Скачать руководство пользователя страница 43

Страница: 43 / 80

Cleaning and care

Plinth filter

Only clean the plinth filter when

Clean out airways

lights up.

To delete

Clean out airways

: Switch the

dryer off and back on again or confirm

with

Removing the plinth filter



Press the round, indented area on the

heat exchanger access panel to open

it.

The panel will spring open.



Pull the plinth filter out by the handle.

Removing the plinth filter will cause the

right-hand guide pin in the dryer to

come out. This pin ensures that the

heat exchanger access panel can only

be closed if the plinth filter is inserted

the right way round.

Cleaning the plinth filter



Pull the handle out of the plinth filter.



Clean the filter thoroughly under

running water.



Squeeze the water out of the plinth

filter thoroughly.



The plinth filter must not be

replaced dripping wet as this can

cause a fault.



Use a damp cloth to remove any fluff

from the handle.

Содержание TKG 450 WP

















































































Результаты поиска

Содержание TKG 450 WP

Отзывы:

Похожие инструкции для TKG 450 WP

Бренды по названию

Популярные бренды

Miele TKG 450 WP, Руководство по эксплуатации

Результаты поиска

Содержание TKG 450 WP

Отзывы:

Похожие инструкции для TKG 450 WP

Бренды по названию

Популярные бренды